0
Typically, when the coil voltage on a relay is decreased gradually, the relay "hold" will release at a certain voltage. This is usually defined as the Drop-out voltage (defined at some minimum value).
Now, in the case of latching relay, the Drop-out voltage is called the Reset voltage.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Why metrosil is provided in differential protection?
under internal fault conditions , CT primary current produces steep insrease in voltage across the relay. This will exceed the burden 3kv normally designed as per. To get protected from the voltage, metrosil is connected across the relay , to drop the voltage.
How would you measure a relays contacts resistance?
The voltage drop across a relay coil will be the same as the coil supply voltage. If you are trying to see if the coil is good or not, remove one of the voltage supply leads and check for continuity by using an ohm meter across the coil leads. A reading will tell you that the coil is intact and not open.
How does a quenching diode work?
Quenching diodes are used to protect the control circuit of a relay. Power is applied to a relay's coil to close it. When this power is released there is a backwards flowing pulse that can wipe out solid state devices like transistors, LEDs, chips, etc... The quenching diode is applied in parallel with the relay coil so that the cathode is on the positive side. During normal operation, the diode doesn't conduct and the relay operates normally. When the relay is switched off, the "reversed" back pulse is absorbed due to the low voltage drop of the diode which limits the spike.
The voltage drop in line can be decreased by?
The voltage drop in a line can be decreased by
What is the effect of diode voltage drop as the output voltage?
The effect of diode voltage drop as the output voltage is that the input voltage will not be totally transferred to the output because power loss in the diode . The output voltage will then be given by: vout=(vin)-(the diode voltage drop).
To change state from liquid to solid?
Drop the temperature.
What causes contact chatter in electrical circuit?
Overload can cause contact chatter. Once the contact closes, the voltage in the circuit collapses and that causes the relay to drop out. At this pint the relay energizes, since the voltage is back. This cycle will continue on.
Why metrosil is provided in differential protection?
under internal fault conditions , CT primary current produces steep insrease in voltage across the relay. This will exceed the burden 3kv normally designed as per. To get protected from the voltage, metrosil is connected across the relay , to drop the voltage.
How would you measure a relays contacts resistance?
The voltage drop across a relay coil will be the same as the coil supply voltage. If you are trying to see if the coil is good or not, remove one of the voltage supply leads and check for continuity by using an ohm meter across the coil leads. A reading will tell you that the coil is intact and not open.
How does a quenching diode work?
Quenching diodes are used to protect the control circuit of a relay. Power is applied to a relay's coil to close it. When this power is released there is a backwards flowing pulse that can wipe out solid state devices like transistors, LEDs, chips, etc... The quenching diode is applied in parallel with the relay coil so that the cathode is on the positive side. During normal operation, the diode doesn't conduct and the relay operates normally. When the relay is switched off, the "reversed" back pulse is absorbed due to the low voltage drop of the diode which limits the spike.
What is volts drop?
the voltage drop means whenever the conductor passing through the supply voltage, according to the resistivity property to reduces the some amount of voltage that drop is known as voltage drop for example the resistance is used to drop the voltage to the circuit.............................................
What is the approximate voltage drop 120 if 10 gage solid copper coated wire is used?
Your question cannot be answered, as we do not know what type of wire the copper is coated on, nor do we know how long the wire is. But, let's assume that it is solid copper # 10 wire 100 feet long. The voltage drop is zero when there is no electricity flowing through it. (That is, 'current', measured in Amperes, or just Amps.) If there is, say, 1 Ampere of current, the voltage drop is close to 1/10th Volt in the 100 feet. If there is, say, 15 Amperes of current, the voltage drop is a tiny bit over 1-1/2 Volts. If you double the wire's length, the voltage drop also doubles, and if the current doubles, the voltage drops also doubles. Or, as in my example, above, if the current rises by 15 times, then the voltage drop rises by 15 times.
What is the voltage drop using?
Voltage drop is caused by circuit resistance
The voltage drop in line can be decreased by?
The voltage drop in a line can be decreased by
What is the effect of diode voltage drop as the output voltage?
The effect of diode voltage drop as the output voltage is that the input voltage will not be totally transferred to the output because power loss in the diode . The output voltage will then be given by: vout=(vin)-(the diode voltage drop).
What cause the voltage drop in shunt generator when its loaded?
because the voltage likes to drop
Why drop voltage in xlpe cable is more than PVC cable?
The voltage drop in a wire has nothing to do with the insulation. Voltage drop has to do with the cross sectional area of the wire.
