0
Explain the Two wattmeter method of power measurement in a 3 phase circuit?
Wiki User
∙ 9y ago
A single wattmeter can measure power due to one phase only. But circuit arrangements , popularly called:
1) 2-wattmeter method (requiring two wattmeters)
2)3-wattmeter method (requiring 3 wattmeters)
can be used for measuring power inn 3-phase circuit. The details of these method can be found in any standard book on electrical engineering.
Wiki User
∙ 15y ago
Wiki User
∙ 9y agoThe normal power measurement for a three-phase system has three wattmeters, each one connected in one of the three live wires, with the voltage coils commoned on the neutral. That measures the three separate powers in the phases.
However the total power measurement is still correct wherever the common point is that the three wattmeters have their voltage coils connected to.
If the three wattmeters have their voltage coils connected to one of the live wires, one of the wattmeters will obviously measure zero watts, but the sum of the other two will still give the total power in the three phases.
Wiki User
∙ 9y agoAll that is needed is one watt meter. The meter will monitor all three phases and compile the power usage into one readout. Up to certain voltages and amperage's the wires are brought to the meter. As the amperage and voltages get higher the measuring equipment is left in the main distribution and small signal wires are run to the meter to give the required wattage readout.
Answer for Single-Phase Wattmeters
If you are referring to single-phase wattmeters and unbalanced loads, then the rule is based on Blondell's Theorem, which states that you can use one less wattmeter than there are number of wires connecting the supply to the load.
Wiki User
∙ 11y agoIt is simple to calculate the power of three phase syste using two wattmeter. In this method,current coils of both wattmeter are inserted any of two line and voltage coil of both wattmeter are connected across third line of three phase system.Then total three phase power is sum or difference of the two wattmeter readings.
Wiki User
∙ 12y agoBlondel's Theorem states that, 'for an unbalanced three-phase load, you can use one less wattmeter than there are wires supplying that load'. So, if you have a balanced three-phase load, supplied with four wires (three line conductors and a neutral), the neutral is redundant (for a balanced load, no current flows through the neutral), so it is equivalent to a three-wire system, so you can use two wattmeters. If, however, the load is unbalanced (with a resulting neutral current), then you would need to use three wattmeters.
Wiki User
∙ 11y ago3
Another AnswerBlondell's Theorem tells us that we can use one less wattmeter than there are wires.Wiki User
∙ 11y agoOnly if the power is balanced between the three phases.
Add your answer:
Earn +20 pts
How would you measure power using three watt meter and one watt meter for balanced and unbalanced loads?
The 'one wattmeter method' can only be used for balanced, wye-connected, loads where the load's neutral point is accessible. The wattmeter's current coil is inserted into any line conductor, and the voltage coil is connected between the same line and the neutral point. The wattmeter reading indicates the power of one phase, so the total power is three times the wattmeter reading.To measure the total power of a balanced or unbalanced wye- or delta-connected load, it is only necessary to use twowattmeters -this is called the 'two wattmeter method'. In this case, the current coils of each wattmeter are inserted into any two line conductors, and the voltage coils are connected between the two line conductors and the third line conductor. The sum of the two wattmeter readings will indicate the total power of the load.
Will the two-wattmeter method work for all three-phase loads eg unbalanced loads inductive loads capacitive loads and delta-connected loads?
Blondel's Theorem tells us that, to measure the total power of a three-phase load (balanced or unbalanced), we can use one less wattmeter than there are conductors supplying that load.So the two-wattmeter method will work for anythree-phase load, provided there are only threeconductors supplying that load, e.g. three-wire delta or three-wire star (wye).Bear in mind that wattmeter's read true power (expressed in watts) and ignores the reactive power of inductors and capacitors.
How would you measure power factor of the balanced three phase load by two wattmeter method?
Yes. The wattmeter's current coil will have to be connected into one of the line conductors, and its voltage coil between that same line conductor and the neutral point of the load. Connected this way, the wattmeter's voltage coil is measuring one of the three phase voltages (line-to-neutral voltage) while its current coil is measuring the corresponding phase current (for a 4-wire system, the phase current = line current). The power factor (cosine of the phase angle) is accounted for automatically within the wattmeter. So the wattmeter will measure the true power (in watts) of one phase. The total power, therefore, will be 3x the wattmeter reading -providing, of course, that the load is balanced (i.e. each phase is identical). WebRep currentVote noRating noWeight
What is the best method to check a unwanted resistance in a circuit?
Do not add any unwanted device in the circuit. Have correct sized wire for the application and the load current.
What is difference between smm7 and POMI?
Standard method of measurement (smm7) & project of international management
Write down the advantage of 2-wattmeter method instead of 3-wattmeter method for measuring ac power?
It's cheaper.
Explain the principle of null-method of measurement?
The null method is used in measuring the unknown EMF of batteries. The method is about using a potentiometer circuit with the battery of a known and then an unknown EMF connected to it one after the other and locating, in each case, the position of the 'null point'; the point on the potentiometer circuit where the current through the battery is zero.
Is there any difference in values between the two wattmeter method and three wattmeter method if you apply these two methods in same load?
Blondel's Theorem states that you can have one less wattmeter than there are conductors supplying a balanced or unbalanced load. In either case, the sum of the wattmeter readings will give you the total power of the load.
Explain in briefly Berkley and Hartley's method of osmotic pressure measurement and states its uses?
brekly and hartley's method
Explain the percentage Method and total outlay method for measurement of Elasticity of demand with the help of sutable illustration?
formula for the arc elasticity of demand
Method of synchronization of an alternator?
there are many ways of synchronization.2.1 Synchronizing lamps2.2 Synchroscope2.3 Synchronizing relaysalso there are wattmeter method and lamp method
Can reactive power measure by 2 wattmeter method?
Active volts amperes are measured by 2 wattmeter methods. A wattmeter will measure active power and not reactive power. Electrical engineering is a promising career for anyone who likes to generate power.
Why is one watt meter method of power measurement not applicable to unbalanced circuits?
The one wattmeter method will only measure the power of the phase to which it is connected. So, by reconnecting it to measure each phase separately, you can measure the power in each phase in turn, and add them up to give you the total power.
Is it possible to measure power factor of the balanced three-phase load by two-wattmeter method?
yes.
How would you measure power using three watt meter and one watt meter for balanced and unbalanced loads?
The 'one wattmeter method' can only be used for balanced, wye-connected, loads where the load's neutral point is accessible. The wattmeter's current coil is inserted into any line conductor, and the voltage coil is connected between the same line and the neutral point. The wattmeter reading indicates the power of one phase, so the total power is three times the wattmeter reading.To measure the total power of a balanced or unbalanced wye- or delta-connected load, it is only necessary to use twowattmeters -this is called the 'two wattmeter method'. In this case, the current coils of each wattmeter are inserted into any two line conductors, and the voltage coils are connected between the two line conductors and the third line conductor. The sum of the two wattmeter readings will indicate the total power of the load.
What is the method of making a rough measurement?
A method of making a rough measurement is: Estimation Answered by :PopTy13
What are the advantages of standard method of measurement?
.
