Want this question answered?
-- If the excitation source is AC, then the steady state of the circuit depends on the voltage, frequency, and waveform (harmonic content) of the source. -- If the excitation source is DC, then the steady state current in a series circuit is zero. DC doesn't pass through a capacitor.
The answer is Kinetic Theory or Kinetic Moleculer Theory
an unclocked flip-flop is the state to which the circuit settles after the inputs change. For a clocked device, the next state is the state after the clock pulse
In a mechanical solenoid, current is applied to a coil, allowing a contact to close (either by a plunger moving to make contact, OR by a hinged/pivoted contact to move to make contact) to complete a circuit and activate a device, such as an ignition/starter. In a solid-state device, there are no moving parts, other than electrons, being routed through diodes, etc., to complete a circuit
The simplest circuit consists of a current source and a resistant element--for example, a battery and an LED bulb. Circuits work by establishing a difference in charge across the terminals of the battery, which can be thought of as pulling or attracting electrons through the wires. The resistant element partially blocks the travel of the electrons, preventing the dangerous state of uncontrolled electron motion known as a short circuit.
In a combinational logic circuit, the output(s) depend only on the present values on the input, not on any previous values. In a sequential circuit, the output(s) also depend on the previous values. A sequential circuit must contain a memory element (at least one flip-flop) to hold the state of the circuit.
Sequential systems extend the idea of combinational logic by including a system state, or in other words memory, to our system. • This allows our system to perform operations that build on past operations in a sequential manner (i.e. one after another).• Timing diagrams will be needed to analyze the operation of many sequential systems.
It was mentioned that there are two different ways to connect two or more electrical devices together in a circuit. They can be connected by means of series connections or by means of parallel connections. When all the devices in a circuit are connected by series connections, then the circuit is referred to as a series circuit. When all the devices in a circuit are connected by parallel connections, then the circuit is referred to as a parallel circuit. A third type of circuit involves the dual use of series and parallel connections in a circuit; such circuits are referred to as compound circuits or combination circuits. The circuit depicted at the right is an example of the use of both series and parallel connections within the same circuit. In this case, light bulbs A and B are connected by parallel connections and light bulbs C and D are connected by series connections. This is an example of a combination circuitBy EngineerMuhammad Zaheer Meer GMS
In general, a sequential circuit is a circuit that depends on a previous state. That means it needs to have some sort of "memory". As the name may suggest, sequence detectors are a good example of a sequential circuit. As bits (1's and 0's) are inputted, it can determine if a certain sequence has been detected. So as each bit gets inputted, it will need to remember it as it gets the next bit. You would need various IC's to create a sequential circuit; most importantly, a memory element of some sort, like a flip-flop.
Combinational Circuit does not depend on the previous and next state inputs but this seqential circuit are dependent on those factors. Clock pulse transition plays a dominant role in sequential cicuit
dear friends, the answer for this question. go to www.google.co.in then type sequential circuit having two d flip flops. u can find the answer for the same question at the top of the page itself.
A combinational circuit's output depends only on its current inputs. This means, it has a truth table. A sequential circuit's output depends on its previous inputs. This means, it's output will depend on which state it is.
A Synchronous Sequential Circuit is a system whose behavior can be defined on the timing of their signals , where in the case of asynchronous sequential circuit depend upon the order in which its inputs signals change and can be affected at any instance of time . (reference : M. Moris Mano)
steps might be present in sequential control of a dishwasher.help me with a block diagram
orgel diagrams cn be draw on the basis of two factors: (1)energy state term (2) mulliken symbols
The Bible states you can if you want more than one wife.
New York State Circuit Courts ended in 1847.