Want this question answered?
Yes, it can be faulty. Some damaged power supplies show good output voltages on the voltage range of a multimeter but, when you connect them, they don't work properly. One possible reason is that maybe an IC in its voltage regulator has a high resistance between the common and the output. You cannot see this by shunting a voltmeter onto it. You have to place a typical load onto the output to test it.
Depends on what the output voltage on the converter is.
In America it should be 60hz. But you can hook up a power meter to the line and find out the real frequency and voltage of the common household or office power line. You may be surprised at the number of spikes and drops in voltage and frequency in a household line. A good UPS can some times tell you as well.
i dont know but if you find one could you let me know as i have this turntable and i am looking for the amplifier gerry
Depending on what type of power supply it is there are a few options.If the 2000mA rating means it'll supply up to 2000mA, you're already okay, although you should put a resistor in parallel with the device to safely dissipate extra power. You wouldn't want to exactly split the supply in case the device has current demand variations. It would probably be best to siphon off say, 750mA. Since it's 12 volts, from ohm's law: V = IR you'd want 12 = 750mA*R, or a 16 Ohm resistor. It would also have to handle the power output, where P = IV, so P = 12v*750mA = 9 W. This is a lot of power, but you could probably find such a resistor somewhere. (Try looking at sandstone power resistors)However, if the supply is powering a sealed device (eg something you wouldn't open up and tamper with), I think you'd be better off just finding the appropriate power supply.
Output Power divided by Power Factor.
You will have to purchase a power supply with a 12 volt DC output capable of handling the current draw of the car radio. Try "google" to find the manufacturer's specification sheet for the radio. In the specs. will be the amp draw of the radio. With this information you will know what amperage the output of the power supply needs to be.
No you can not. The power supply output of 5 volts is under sized. There is no way that a 45 volt device would operate from it. You will need to find a power supply of 45 volts.
This switching power supply is ideal for DIY projects like light bulbs, motors and other electronics. The output voltage is DC 12V constant voltage, which means that no matter what the state of charge on your battery is, this power supply will output the same voltage. This Switching Power Supply is a smart choice for your home or office working environment
Yes, it can be faulty. Some damaged power supplies show good output voltages on the voltage range of a multimeter but, when you connect them, they don't work properly. One possible reason is that maybe an IC in its voltage regulator has a high resistance between the common and the output. You cannot see this by shunting a voltmeter onto it. You have to place a typical load onto the output to test it.
by using tester
To find the power supply look at a schematic for the fuel injection system in a service manual for the vehicle they are in.
Find out what the VA capacity of the power supply is and then add up the connected load in VA (volts x amps). If the load totals are greater that the VA power supply capacity then this is where the heat is coming from. The power supply is overloaded. Remove some of the load or get a bigger capacity power supply.
I have one bout to post on ebay im not sure what its for but its ITE POWER SUPPLY MODEL U120650A63 WHATS IT FOR?
The quickest place to find a Dell Inspiron power supply may be on Amazon. You can also contact your local Dell supplier and ask them for their assistance.
Its usually written on a label on the outside of the power supply box. The number will specify Watts, i.e.150W for 150 Watts
Output equals efficiency times input; in formula, Ot = Ef x In and so In = Ot/Ef. To calculate the original input, divide the output by the efficiency.