A liquid has a constant volume but no fixed shape.
Any fluid.
It increases very slightly, which is why a corroded nut and bolt are so hard to undo.
It all depends on the size of the three items - a metal cube with volume 1 cm3 will weigh far less than one of the bolts they used to attach the space shuttle to the launch pad, correct? And it also depends on the metals in question - an iridium cube will weigh more than a magnesium nut made from the same volume of metal, because iridium is very heavy and magnesium is much lighter. If you had these three objects all of the same metal and they all weighed the same, the cube would be smaller because a cube is a more compact shape than a nut or bolt.
The pili shell has 3.2% moisture content, 11.9% volatile combustible matter, 11.1% ash and 77% fixed carbon.~Based on the book:"Pili Nut, Canarium Ovatum Engl" By Roberto E. Coronel
Combretum bracteosum is the scientific name of the hiccup nut. Some people say the nut causes hiccups and some say it cures them.
The nut will get burnt. It's pretty hard to light a nut on fire, and even if it does catch on fire, it will go out in less that 5 seconds.
A kidney shape nut is a cashew nut. This is considered to be a riddle.
One method would be with water displacement. Fill a graduated cylinder with a known amount of water. Drop in the nut. Push below surface with wire, or something with negligible volume. Read volume, and subtract.
A hexagonal nut has the shape of an equilateral hexagon
I got it. The nut is said to be stripped if it begins to lose its original shape (hex or other). This will make it difficult to grip the nut with tools.
A stripped truss rod nut can indeed be fixed. There are special not retrieving sockets that may do the trick- they are often in the automotive section of hardware stores. Sometimes these are too bulky to fit in the nut cavity. In this case you either have to visit a luthiery supply site and purchase the specific(costly) tools. The best bet in the end will be to take this to a guitar tech.
I had a coco nut
the filler nut is to the left of the handbrake drum on the back of the transfer case.the nut only has 4 sides to it not hexagon shape.
It increases very slightly, which is why a corroded nut and bolt are so hard to undo.
It all depends on the size of the three items - a metal cube with volume 1 cm3 will weigh far less than one of the bolts they used to attach the space shuttle to the launch pad, correct? And it also depends on the metals in question - an iridium cube will weigh more than a magnesium nut made from the same volume of metal, because iridium is very heavy and magnesium is much lighter. If you had these three objects all of the same metal and they all weighed the same, the cube would be smaller because a cube is a more compact shape than a nut or bolt.
The kinematic equation for velocity states that Vf = Vo + at. Assuming that the nut starts from rest, Vo goes to zero. This means that the final velocity of the nut is the gravitational constant times time i.e. Vf = at. If the nut falls on earth then the final velocity would be 98.1 m/s or 322 ft/s.
First, Determine what type of bike trailer hitch system you have. There are quick-release skewers and fixed-nut attachments. The quick-release skewer is just a squeeze clamp and strap that attaches around the bike seat post. The fixed-nut attachment is a horizontal hole through the trailer hitch that will bolt to the rear bike wheel. Second, Unscrew the nut holding on the rear tire. This is necessary for the fixed-nut attachment bike trailer hitches. Third, Slide the fixed-nut attachment trailer hitch over the rear wheel bolt protruding through the bike frame. Screw the nut back on tightly. Fourth, Wrap the strap around the bike seat post under the bike seat. This is necessary for the quick-release skewer bike trailer hitches. Lastly, Squeeze the clamp on the quick-release skewer. Feed the strap back through the quick-release skewer on the bike trailer. Release the clamp on the quick-release skewer. Pull the strap tight.
The main reason is so that vandals with a regular wrench cannot turn a square nut and steal water. But since this is about geometry it is probably since the nut is soft and made of brass that a square wrench would round the nut and damage it quickly. Having a pentagon shape gives more area for the wrench to grip and a triangle is the strongest geometric shape so the force is more distributed from the points to the center of the shaft. That lets you turn it with force without stripping or damaging the nut.