0
horizon7.jpg
peman bahadorani
Add your answer:
Earn +20 pts
What cdi command should you enter to display the command syntax help so that can you learn how to complete a command that begins with config?
1. commandname --help {this command is used to view the help documents of the commands} Ex: config --help {displays the help document for config command} 2. commandname info {to view the information about any command} Ex: config info {displays the info for config command} 3. man commandname {to view the mannual page of commands for syntax} Ex: man config {displays the manual for config command}
When prompt and command must be entered to view the configuration stored in NVRAM?
show startup-config
How can an IP address for a network device be assigned to a particular network?
Router(config)# hostname AdminAdmin(config)# enable secret cangetinAdmin(config)# interface fa0/1Admin(config-if)#ip address 192.168.1.22 255.255.255.248Router(config)# hostname AdminAdmin(config)# enable password cangetinAdmin(config)# interface fa0/1Admin(config-if)# ip address 192.168.1.22 255.255.255.248Router(config)# hostname AdminAdmin(config)# enable secret cangetinAdmin(config)# interface fa0/0Admin(config-if)# ip address 192.168.1.22 255.255.255.248Router(config)# hostname AdminAdmin(config)# enable password cangetinAdmin(config)# interface fa0/0Admin(config-if)# ip address 192.168.1.22 255.255.255.248
Where is the vanishing point for a birds eye view?
Above the horizon
What is VMWare VDI Horizon View?
VMWare VDI Horizon View is a virtual desktop manager and planner. This application helps simplify desktop and application management while improving security.
Where do startup-config and a running-config reside in Cisco equipment?
startup-config resides in NVRAM and running-config resides in RAM.
Configure NAT to allow PC3 to ping PC1?
R3#configure terminalR3(config)#access-list 104 permit ip 10.0.0.128 0.0.0.127 anyR3(config)#ip nat inside source list 104 interface Serial0/0/0 overloadR3(config)#interface fastEthernet0/1R3(config-if)#ip access-group 104 inR3(config-if)#ip nat insideR3(config-if)#exitR3(config)#interface Serial0/0/0R3(config-if)#ip nat outsideR3(config-if)#exitR3(config)#interface Serial0/0/1R3(config-if)#ip nat outsideR3(config-if)#endWriting by vanhuuvt32bonphuonglanha@gmail.com
What is the command to remove the console password router?
Remove Console password router>enable router#configure terminal router(config)#line console 0 router(config-line)#no login router(config-line)#no password router(config-line)#exit router(config)#exit
What command do you type to save the configuration stored in RAM to NV RAM?
Router(config)#Copy running-config startup-config
How do you configure RIP routing protocol on a Cisco router?
Here is a basic overview of the configuration of RIP on a Cisco router:Router(config)#router ripRouter(config-router)#network 192.168.1.0Router(config-router)#network 192.168.2.0Router(config-router)#network 192.168.3.0Router(config-router)#network 192.168.4.0Router(config-router)#network 192.168.5.0The 192.168.x.0 address can be changed to whatever address you would like to be broadcast over RIP. There are also other settings that can be configured.If you use RIPv2 you can also have the following configuration:Router(config)#router ripRouter(config-router)#version 2Router(config-router)#network 192.168.1.0Router(config-router)#network 192.168.2.0Router(config-router)#network 192.168.3.0Router(config-router)#network 192.168.4.0Router(config-router)#network 192.168.5.0Router(config-router)#exitRouter(config)#exitRouter#%SYS-5-CONFIG_I: Configured from console by consoleRouter#copy running-config startup-configDestination filename [startup-config]?Building configuration...[OK]Router#
How long is the viewing of the ISS from earth?
3 minutes and then its out of the horizon too view
When was Pkg-config created?
Pkg-config was created in 2006.
