answersLogoWhite

0


Best Answer
Copy

Its fairly simple. First, you'll have to remove the old horn. There will be a cable you need to remove, with a locking snap, like every other electrical connection in the car. Remove that, then proceed to remove the retainer bolt from the horn's mounting arm. After you get the old horn out, save the screw that held the arm in, and re-use the arm if it fits on the new horn, but it probably won't.

If you bought a generic horn, you'll need to cut off the wire connector, and solder on whatever connectors the horn uses. This is a pain, as the wire isn't long enough to bring down and solder.

Once you've soldered the connectors on, mount and connect the new horn in the same place the old one was located. Check the fuse, and test.

User Avatar

Wiki User

โˆ™ 2015-07-15 21:30:28
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How Do you Install A Horn?
Write your answer...
Submit

Related Questions

How do you fix the horn on a 1988 delta 88?

buy a new horn and install it


How can I install an air horn on a motor home?

In order to install an air horn on a motor home you will need to but the air horn kit and follow the direction supplied within. Although air horns are generally limited to semi's.


How do you install a horn in a Chevrolet s10 truck?

first off, which end of the horn are you needing to install, under the hood is one thing, in the steering column is a whole diff story.


How Dow I unplug the horn to install the battery on a 2004 Malibu Maxx?

You don't have to unplug the horn to replace the battery.


How do you replace the horn on 1996 Chevy Corvette?

Begin by removing the wiring harness from your 1996 Chevy Corvette horn. Remove the horn retaining bolts. Reverse the process to install the new horn.


How do you replace horn on a Dodge Ram 1500 1995?

Remove the wiring harness from the back of your 1995 Dodge Ram horn. Remove the horn retaining bolts. Reverse the process to install the new horn.


How do you install a horn for a Toyota Celica?

You don't...you trade it in for a better car.


How do you disconnect the horn in the steering column and install an external horn switch on a 1980 Chevy silverado?

it is easier to repair the OEM horn assembly than to "rig" up a button


How do you install a horn in a 1992 Toyota Camry?

open the hood, behind the grill, it should be on the left side(the horn), disconnect the wires running to it and unbolt it. take your new horn and bolt it on, then run the wires back to the new horn.


How do you replace the horn button in a 1992 Bonneville?

You can replace the horn button on your 1992 Pontiac Bonneville by removing the center steering will cover. Remove the horn button retaining screws. Remove the horn button wiring harness. Reverse the process to install your new horn button.


How does one install car air horns?

You can install car air horns by opening the hood of the vehicle and choose the best place to position it, use self tapping screws to mount the horn, place the compressor to the tubing and test the horn.


Can you install police sirens in my car?

If you are in the United States, Unless you have authorization, you can only install a P.A. and Electric Air horn on your vehicle. It is otherwise illegal to possess or install an emergency siren.


How do you replace the horn in a 1999 Pontiac Grand Prix?

First there are 2 nut, side by side of the Passenger Headlight. Unscrew it, and remove the Headlight. The Horn is now on your face, Unscrew the Nut and Install the New Horn.


How do you install a horn into a 1969 VW beetle?

The horn sits under the front of the car, and it's bolted to the "frame". Undo the wires that are on the old horn, and remember where the came from so you can put them in the same order on the new horn. If you have the correct horn, the same wiring configuration should work, and you just bolt it on.


Can you wire up a horn to car battery?

Answer 1Yes, but... you will need wire heavy enough to carry the current [measured in Amperes or Amps] that the horn uses, and also need to install a control switch in the circuit or the horn will sound continuously. The hookup is simple: one horn wire to the Positive [+] terminal and the other horn wire to the Negative [--] terminal.It would also be a very good safety practice to install a properly sized fuse in circuit to protect the conductor wires.


How do you fix a horn on a 1999 Saturn SL1?

1. Remove the driver's side headlight. 2. Unbolt the horn and bracket from car. 3. Get replacement 3-wire horn. (available from Saturn for ~$70) 4. Install new horn and bracket on car. 5. Intall headlight.


How much should it cost to replace the horn on a 2001 Dodge Neon?

If it's just the horn itself...$20 buck for the new horn. install it yourself with the Haynes repair manual, Dodge Neon 2000 thru 2003. Book #30036. The horn is under the passenger headlamp.


How would you install a horn that is connected to the battery and a push button?

if the horn is already there and is bad, just disconnect the two wires on it, unscrew horn, remove it and reinstall the new one and reconnect the wires. If you don't have a horn, then find a suitable place under the hood and drill X number of holes. The switch is wired in series with the battery and horn. The button is placed at a convenient place you can get to it when you want to blow the horn.


How do you add a relay for a second separate horn on a 1998 Honda CRV without modifying the existing horn setup?

If you're just adding a second horn that sounds at the same time as the original equipment horn - you will need to cut into the wire that leads to the original equipment horn in order to get power to the added one. Install the additional horn making sure it is securely grounded. Then, splice the power line to the new horn into the power wire to the existing horn. This will ensure that when the horn button is depressed, both horns will receive power simultaneously.


How do you install a bass blocker to a selenium horn?

The same way you would any other horn the bass blocker go's on the positive terminal. and put the positive wire on the other end of the bass blocker. and then put the negitive wire on the negitive terminal of the horn


How do you install new horn for 1990 jeep Cherokee in the steering wheel?

the horn is not in the steering wheel only the switch to make it workis in the steering column note if you didnt know horn is not in steering column, u would be better off getting a mechanic to fix it


How do you remove horn assembly from XL1200L harley Davidson sportster to install engine guard?

all you have to do is remove the 2 bolts where the motor mounts are which should be right above the horn. after removed take the bracket off and replace bolts and you will have successfully removed the horn assembly.


93 Chevrolet wagfullsizehorn contactskeep brakingi am on your 4th one20.00eagenunine GMCparts?

Install an auxilliary horn button on dash board


How do you fix a car horn that wont beep?

Buy a new one, uninstall the old one, install the new one.


How do you install an ooo gah horn that is connected to the battery and has a push button?

Connect the positive lead to the battery or a spare positive terminal at the fuse panel, run it to the switch with an in-line fuse, run from there to the positive terminal on the horn. Mount the horn and connect the ground wire to ground on the chassis.