answersLogoWhite

0

The fact that it is a dry contact has nothing to do with the amount of voltage it will handle. Contact voltage capacities are rated by the air space between live parts. The further the space, the higher the voltage will be allowed. What limits the contacts are the amount of current they can conduct. Usually relay contacts have the contact rating printed on the side of the relay enclosure. The terminology of a dry contact is, a contact in another piece of equipment that is used to close a relay in a "hot" complete circuit. e.g. An automatic transfer switch has a dry contact that when it closes on a power failure it closes the circuit for the engine start circuit to start the generator.

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

What is a 2A Dry contact?

A dry contact is a contact that does not supply voltage. In the realm of contactors and relays, it is simply a contact or set of contacts that switches another user-defined circuit. It doesn't provide any voltage on its own, it just opens and closes, much like a switch. A 2 amp dry contact is rated for up to 2 amps of current at the stated voltage, which is also likely stamped on the contact.


What is the difference between dry and wet contact?

A dry contact is a contact that does not provide voltage. For instance, the push-to-talk switch of a microphone, which just closes a circuit without providing voltage. A wet contact is a contact that will provide voltage when closed, like the switch on the wall that activates the 110 VAC outlet to turn a lamp on in a room. / +------o o---------(o) | +---------------------(o) Dry contact / +------o o---------(o) | --+-- --- Wet contact ------ -+- | +---------------------(o)


Is dry a contact or non-contact force?

"Dry" is not a force.


What is a dry contact and no volt contact in the context of electrical engineering?

A "dry" contact is a contact that is not initially connected to a voltage source. It could be stand-alone, such as a pressure switch mounted on a boiler. Or, if the contact is mounted as part of an electrical unit that has a power source, then the "dry" contact has no pre-wired electrical connection to that power source. For example, a magnetic motor starter may have an extra contact that is not connected to the control circuit that starts and stops the motor. However, when the motor starts, the "dry" contact changes state, because the mechanical action of the starter moves the contact. This "dry" contact could then be wired to devices/circuits that are separate/remote from the motor starter circuits. I do not recognize the term "no volt contact" but I suspect that it is the same thing. A specific type of dry contact in the USA is a "form C" contact which is a three wire contact: Normally Open(NO), Normally Closed (NC), and a Common (C).


When is a circuit considered a dry circuit?

when contacts on a switch or relay does not melt enough surface to allow current flow


What happens when you disconnected the wire from the dry cell?

when the wire is disconnected from the dry cell you feel not hot


What do you do if contact lenses are dry?

Put some drops of the solution on the dry lenses.


What is wet contact in the context of electrical engineering?

what is the meaning of term of Dry Contact ?


How do alternator belts break?

Worn, loose, or dry rotted. They just break with age.


What is the difference between contact cement and fast dry cement?

Contact cement is already dry on contact, and is very different from other adhesives because it needs to air-dry for 15 to 20 minutes before assembling. As for fast dry cement, special patching dry very fast depending on manufacturer some are as fast as 1 hour.


What is a slogan for spring break?

"Don't be dry! Get high!"


What happened to the reading of ammeter and voltmeter if the number of dry cells are added in the circuit?

Well, isn't that just a happy little question! When you add more dry cells to a circuit, the ammeter will show a higher reading because there is more current flowing through the circuit. The voltmeter reading will also increase because the total voltage of the circuit will be higher with the addition of more dry cells. Just remember to always paint with light and electricity in your circuits, my friend!