0
How are branch circuits protective device affected when the conductors used are of a larger size than called for by the code?
Wiki User
∙ 12y agoWant this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
DoesCode permit connecting receptacles to a 20ampere branch circuit using short lengths of 14AWG conductors as the pigtail between the receptacle terminals and the 12AWG branch-circuit conductors?
No. This practice is a violation of Article 210.19 (A) of the NEC. "Conductors of branch circuits supplying more than one receptacle for cord-and-plug-connected portable loads shall have an ampacity of not less than the rating of the branch circuit."
What ampacity should branch circuit conductors have?
Branch circuits wire sizes are governed by the connected load amperage of the circuit. The wire size ampacity then governs the size of the breaker that is used to protect the circuit from overloading. For general home wiring circuits the conductors used are, receptacles and lighting #14 - 15 amps, dedicated circuits load dependant, hot water tank and baseboard heaters #12 - 20 amps, clothes dryer #10 - 30 amps, range #8 -- 40 amps.
What are feeders in power system?
"Feeders" are conductors which carry electric power from the service equipment (or generator switchboard) to the overcurrent devices for groups of branch circuits or load centers supplying various loads.
Can branch circuits from a panel be pulled in the same conduit if not exeeding the conduit fill requirements?
Yes. The thing that has to be closely watched is the load on the conductors. The conductors will have to be de-rated as the code only gives amperage rating for three conductors in a raceway. So watch the connected amperage to each load and fill the conduit accordingly. This supersedes the conduit fill requirements rule.
How are branch circuits rated?
By the rating of the overcurrent device.
What size conductors are to be used small appliance branch circuits?
All small appliance branch circuits, typically kitchen, are required to be 12awg. Cu., or 20 amp.
What is the meaning ofjunction box?
A box through which the main conductors of a system of electric distribution pass, and where connection is made with branch circuits.
What is the meaning of junction box?
A box through which the main conductors of a system of electric distribution pass, and where connection is made with branch circuits.
DoesCode permit connecting receptacles to a 20ampere branch circuit using short lengths of 14AWG conductors as the pigtail between the receptacle terminals and the 12AWG branch-circuit conductors?
No. This practice is a violation of Article 210.19 (A) of the NEC. "Conductors of branch circuits supplying more than one receptacle for cord-and-plug-connected portable loads shall have an ampacity of not less than the rating of the branch circuit."
What ampacity should branch circuit conductors have?
Branch circuits wire sizes are governed by the connected load amperage of the circuit. The wire size ampacity then governs the size of the breaker that is used to protect the circuit from overloading. For general home wiring circuits the conductors used are, receptacles and lighting #14 - 15 amps, dedicated circuits load dependant, hot water tank and baseboard heaters #12 - 20 amps, clothes dryer #10 - 30 amps, range #8 -- 40 amps.
How is the rating of the branch-circuit protective device affected when the conductors used are of larger size than called for by the code?
There is no problem using over sized wires on a breaker. It is only when the wires are undersized that the trouble begins. Oversize wire on a breaker is very common practice when overcoming voltage drop on a circuit.
How is the rating of the branch circuit protective device affected when conductors used are of larger size than called for by the code?
There is no problem using over sized wires on a breaker. It is only when the wires are undersized that the trouble begins. Oversize wire on a breaker is very common practice when overcoming voltage drop on a circuit.
What are feeders in power system?
"Feeders" are conductors which carry electric power from the service equipment (or generator switchboard) to the overcurrent devices for groups of branch circuits or load centers supplying various loads.
Explain a Branch Circuit?
i want the details regarding the branch circuits
Can branch circuits from a panel be pulled in the same conduit if not exeeding the conduit fill requirements?
Yes. The thing that has to be closely watched is the load on the conductors. The conductors will have to be de-rated as the code only gives amperage rating for three conductors in a raceway. So watch the connected amperage to each load and fill the conduit accordingly. This supersedes the conduit fill requirements rule.
What article in the NEC tells you what size breaker is used for 14awg 120v receptacle?
The article designations may change with the code cycle year. In the 2005 NEC see table 310-16 (allowable ampacities for conductors), also article 240.4(D) (protection of small conductors), also table 210.24 (summary of branch circuit requirements for muti-outlet branch circuits)
What is the code ruling in the US on 3 phase branch circuits and the neutral?
A three phase system will have 3 phase branch circuits and no neutral.
