Actually, they are not related. They are two separate components. To illustrate: take a waterfall for example. The current (amperage) flowing over the waterfall is the current or amperage (how much water is going over the waterfall. The Voltage is, essentially, the potential energy available. If the water fall is 100 feet tall it will have significantly more "voltage" than if it is only one inch tall. A 100 foot high water fall that has only one drop of water per second going over it will have a high "voltage" but a very low current. A one inch waterfall have 300,000 gallons per second going over it will have a very high "current" but low voltage. So concerning an electrical circuit, if one of the current or voltage are low enough it will not harm you regardless of how high the other one is. Volts and amperage together basically combined in a formula to determine the number of watts, but they are not specifically related to each other.
As per Ohm's law V=IR where V is voltage, I is current and R is resistance. since Voltages is equal to current times resistance than makes them directly proportional to each other and therefor related.
Current and voltage are related in a circuit through Ohm's Law, which states that voltage is equal to the current multiplied by the resistance of the circuit (V=IR). In other words, an increase in voltage will result in a proportional increase in current if the resistance remains constant, and vice versa. Ohm's Law helps to understand and predict the behavior of electrical circuits.
The current between any two points in the circuit is the voltage between
those two points divided by the resistance between the same points.
The current between any two points in the circuit is the voltage between
those two points divided by the resistance between the same points.
Changing the voltage in a circuit will alter the current flowing through it. According to Ohm's Law, the current is directly proportional to the voltage in the circuit. Increasing the voltage will lead to an increase in current, and vice versa.
In a series circuit, the current remains constant throughout the circuit. The voltage across each component in a series circuit adds up to the total voltage of the circuit.
To convert voltage to milliamps, you need to know the resistance in the circuit. You can use Ohm's Law (I = V/R), where I is current in amps, V is voltage, and R is resistance in ohms. To convert amps to milliamps, multiply the result by 1000.
Electric current flows when there is a closed circuit with a pathway for electrons to move from a higher voltage point to a lower voltage point. When the circuit is complete, the flow of electrons creates an electric current.
In an inductive circuit, the current lags behind the voltage due to the energy stored in the inductor's magnetic field. The voltage leads the current by 90 degrees in an ideal inductive circuit. The relationship between voltage and current is described by the equation V = L di/dt, where V is voltage, L is inductance, di is change in current, and dt is change in time.
Voltage = (current) x (resistance) Current = (voltage)/(resistance) Resistance = (voltage)/(current)
in ac circuits power,P=VICOS@ @ is the angle between voltage and current. in dc P=VI V is the voltage I is the current. Power (in Watts) is current (A) x voltage (V)
Voltage attempts to make a current flow, and current will flow if the circuit is complete. It is possible to have voltage without current, but current cannot flow without voltage. The answer is "yes",voltage remains the same as current moves through the circuit.As the voltage remains constant, current increases in the circuit.
In a series circuit, the current remains constant throughout the circuit. The voltage across each component in a series circuit adds up to the total voltage of the circuit.
In this case current flows from a high voltage to a lower voltage in a circuit.
Voltage = (current) x (resistance) Current = (voltage)/(resistance) Resistance = (voltage)/(current)
Voltage = (current) x (resistance) Current = (voltage)/(resistance) Resistance = (voltage)/(current)
A voltage error circuit is called an error amplifier and happens when there are discrepancies between the voltage output and the reference voltage. A current error circuit happens when there is a disruption of flow in an ammeter.
Inductive. Voltage (E) leads current (I) in an inductive (L) circuit and current (I) leads voltage (E) in a capacitive (C) circuit. (ELI the ICEman)
The current between any two points in the circuit is the voltage between those two points divided by the resistance between the same points.
Voltage leads current or, more specifically current lags voltage, in an inductive circuit. This is because an inductor resists a change in current.
To convert voltage to milliamps, you need to know the resistance in the circuit. You can use Ohm's Law (I = V/R), where I is current in amps, V is voltage, and R is resistance in ohms. To convert amps to milliamps, multiply the result by 1000.