Hyundai
Ford Ranger
Timing Belts and Chains
Ford Ranger XL

How are the timing marks lined up on a 1992 Hyundai 1.5?

353637

Top Answer
User Avatar
Wiki User
2014-10-07 02:15:56
2014-10-07 02:15:56

The timing marks on a 1992 Hyundai 1.5 are lined up by placing the indicators on the cam sprocket and crankshaft sprocket across from each other. This sets the initial timing which determines which determines the synchronization between the engine's internals.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The timing marks on a 1992 Toyota Camry 4sfe are timing belt replacement marks.

User Avatar

The timing marks, on your 1992 Toyota, are located on the main engine pulley. The timing marks can be found around the perimeter of the pulley.

User Avatar

No need for timing marks on the outside of the engine that has no adjustable ignition timing.(DIS)

User Avatar

The timing marks can be found on the flywheel and the front pulley on the front of the engine. The timing marks indicate when a certain piston is at its top stroke.

User Avatar

Where are the timing marks on a 1992 Toyota Paseo 16 efi 1.5 liter engine?

User Avatar

ford doesnt put timing marks on anything. u need a special cam gear alignment tool

User Avatar

clean on the front of the pump on top where it bolts on the motor there are timing marks there line up the long marks to set the timing.

User Avatar

can u give me a diagram on the timing marks for my 95 hyundi elantra

User Avatar

I just changed a timing belt in a buddys 1990 accord and you need to set the marks on the pulleys to same direction as your crank pulley mark is.

User Avatar

number1 piston up timing marks align with each other

User Avatar

Dodge didn't make a Neon until 1995.

User Avatar

The marks are on the bottom pulley , you may need to get a white marker to hi light it , so it will be easier to see with a light .

User Avatar

The timing is set by timing marks on the crankshaft pulley. Using a timing light the light will sync with the engine and show if the marks line up properly. To adjust the timing the distributor is turned slightly. There is a clam and bolt under the distributor, loosen these just a bit to be able to move the distributor.

User Avatar

Get a manual on your car, It will have pictures and everything,.

User Avatar

timing marks should be on the harmonic balance.above harmonic balance should be a a flat metal pointer. the edge of this pointer will lign up with marks when being timed

User Avatar

Get the Haynes manual for the unit, they have a good, detailed diagram on aligning the timing marks on the timing gears being turned by a chain. There is no belt on this engine.

User Avatar

After disassembling to expose timing belt, look for TDC and ATDC timing marks. Align them, allowing 43 centimeters. Set BTDC mark in like manner.

User Avatar

What is the set timing of a 1992 Mitsubishi Expo?

User Avatar

its a Hyundai and its Korean made...

User Avatar

I have a 1992 Camry LE and its a belt

User Avatar

Both the crank and cam sprockets have timing marks on the sprocket and on the engine. As you face the front of the engine, with the sprockets in front of you, the cam timing mark is approx. 85 degrees right of top center. The crank mark is approx. 10-15 degrees right of top center (piston #1 should be top dead center). Line marks on sprockets with timing marks on block (tin), slip on belt and tighten tensioner. Manually rotate engine 2 complete revolutions and check that both marks are still aligned.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.