0
00 is 10.0mm across or 3/8 ths of an inch across
Wiki User
∙ 14y ago
Wiki User
∙ 14y agoA 00 Gauge is a approx. 9 mm
That's a little bit bigger than your normal yellow pencil
Add your answer:
Earn +20 pts
How much is an ear gauging set?
it depends where you buy it from but once on eBay i saw a set for 10 pound It also depends on the size of the set, the material of the tapers and plugs, and whether you get a set with plugs or tunnels. The flare of the jewelry can sometimes change the price too. On average, a full-steel set from 14ga-00ga costs about $45. If you just want to buy a steel taper and plug set for one size, that's about $9.
How Big Are These Ear Plugs?
probaly the normal size of earplugs
How long do you wait before putting a bigger gadge in your ear?
For sizes 20ga to 6ga Wait at least 3 weeks. 6ga to 0ga should be at least a month. 00ga and larger should be a month and a half to two months. But, for sizes larger than 00ga you usually use tape to stretch up so you can start taping up after 2 weeks since tapers arent made in those large sizes.
How many spark plugs is use for a 1976 dodge D100 with a 360 big block?
( 8 ) spark plugs for your 360 cubic inch V8 engine
What is the next three sizes up in gauging your ears after 00?
The term is stretching, not gauging. While gauge can be a verb, if you go to any reputable shop and talk to them they will laugh at you if you say gauge. after 00ga, the next size is either 10mm (sometimes 000ga) or 11mm (7/16"). 00ga can be 9mm or 10mm so it would be best to find out before you attempt to stretch up. Glass, steel, and titanium are the only materials for a fresh stretch, so if you have been stretching with acrylic at this point, don't do that anymore! www.bodyartforms.com has wonderful products at extremely reasonable prices, and they accept cash, so there is no reason not to have suitable materials for stretching! The sizes go like this: 00ga, 7/16", 1/2", 9/16", however, 00ga can be 9mm or 10mm (as I stated), 7/16" is 11mm, 1/2" is 13mm so you need to stretch to 12mm first. Many fractions of an inch sizes have mm sizes in between, like so: 00ga (9mm/10mm), 7/16" (11mm), 12mm, 1/2" (13mm), 9/16" (14mm), 15mm, 5/8" (16mm), 11/16" (17mm), 18mm, 3/4" (19mm), 20mm, 13/16" (21mm), 7/8" (22mm), 23mm 15/16" (24mm), 1" (25/26mm) Good luck!
After changing spark plugs on a 2001 issuzu rodeo car has a big vibration any idea what this may be?
make sure you put the right plug wires to the plugs and you did not mix them up drive safe
What to do with p0302 code on a 2000 Nissan Quest?
You have a misfire on cylinder number 2. Start with replacing the spark plugs. That's a big job on those vehicles, so the spark plugs that are in there are probably the original ones.
How do you replace the spark plugs on a 98 Subaru Impreza 2.5 - What size ratchet should you use to get out the old spark plugs?
any size that works usually a 3/8th ratchet You probably meant what size socket Its either 5/8th if the plugs are small or 13/16th if they are big
Where are the spark plugs located in a 1984 caprice?
depending on the engine size they will be located in the sides of the heads. look for a rotor cap and 6 or 8 big wires, depending on the engine, then foller them rihgt down to the spark plugs.
How do you change plugs on Hyundai Santa Fe?
Well it is easy to get to the front spark plugs but you are going to have to take off the intake manifold to get to the rear ones. Not an easy job. Probably have to pay big bucks at a garage to do this unless you can do it yourself.
How many ignition coils are there in a 1997 jeep wrangler?
One big one that goes across all 6 spark plugs.
Why is your diesel car hard to start and when it does it blows out a big cloud of black smoke but then runs normally?
Possibly bad glow plugs.
