answersLogoWhite

0

Most likely, if you have to ask, you shouldn't do it. You would have to either tear up the floor, go under the house, or rip open the ceiling, depending on whether the said bathroom is on the first floor or second floor.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

Why is my bathroom sink leaking underneath?

Your bathroom sink may be leaking underneath due to a worn-out or damaged seal, loose connections, or a cracked pipe. It is important to identify and fix the source of the leak to prevent water damage and mold growth.


If I have a water leak underneath the slab of my bathroom will the slab need to be broken in order to repair it?

I think I have a water leak in my bathroom under the slab. Will a plumber have to break my slab to fix it?


What do you do to the spaceship broken in the mud on popropica?

You have to fix the broken pipe on the spaceship by dragging the fuel rod onto it.


How do you fix PVC bathroom sink pipe under trailer?

The same as any other PVC drain. Trailers have a plastic or fabric covering underneath. Cut this at the drain and repair the pipe. Duct tape the cut in the fabric or staple a section of cheap blue tarp over that section.


How can I fix a broken PVC pipe?

To fix a broken PVC pipe, you can cut out the damaged section using a hacksaw, clean the ends of the pipe, and then use PVC primer and cement to attach a new piece of PVC pipe or a coupling to the existing pipe. Make sure to follow the manufacturer's instructions for the primer and cement for a secure and leak-free repair.


How can I fix a broken tile in my bathroom?

To fix a broken tile in your bathroom, you will need to remove the broken tile, clean the area, apply adhesive to the back of the new tile, place the new tile in position, and grout around the edges. Allow the adhesive to dry completely before using the area.


Why is my bathroom sink drain leaking and how can I fix it?

Your bathroom sink drain may be leaking due to a loose connection, worn out gasket, or a damaged pipe. To fix it, you can try tightening the connections, replacing the gasket, or repairing the pipe with plumber's tape or sealant. If the issue persists, you may need to seek professional help to properly fix the leak.


Hot spot on floor in bathroom?

A hot spot on the floor in the bathroom can indicate an issue with the plumbing system, such as a leak, clog, or broken pipe. It is important to identify and address the source of the heat to prevent further damage or potential hazards. Contacting a professional plumber to inspect and fix the problem is recommended.


How can I fix a loose bathroom faucet handle?

To fix a loose bathroom faucet handle, you can try tightening the screw underneath the handle using a screwdriver. If that doesn't work, you may need to replace the handle or the cartridge inside the faucet.


How can I fix a broken sprinkler pipe?

To fix a broken sprinkler pipe, you will need to first locate the damaged section of the pipe. Once you have identified the break, you can cut out the damaged portion and replace it with a new section of pipe using PVC pipe and fittings. Make sure to properly secure the new section in place and test the repair by turning on the sprinkler system to check for leaks.


How can I fix a broken water pipe outside?

To fix a broken water pipe outside, you will need to first locate the source of the leak. Once you have identified the broken section, you can shut off the water supply to that area and then repair or replace the damaged pipe. This may involve cutting out the broken section and installing a new piece of pipe, or using a repair clamp or epoxy to seal the leak. It is important to follow proper safety precautions and consider hiring a professional plumber if needed.


How can I fix a broken pipe?

To fix a broken pipe, first turn off the water supply to prevent further damage. Next, cut out the damaged section of the pipe using a pipe cutter or hacksaw. Clean the edges of the cut pipe and the replacement section. Apply pipe joint compound or plumber's tape to the fittings and connect the new section to the existing pipe. Tighten the fittings securely and turn the water supply back on to check for leaks.