The smallest size in breaker panels is 30 amps and the smallest breakers that can be installed into a 30 amp panel are15 amps.
If more info is needed go to the discussion page tab and explain what you are trying to do.
Depends on the size of the wire going to the A/C. If the wire is AWG #10 you cannot install a 40 amp breaker. If the wire is AWG #8 you can.
Yes.Additional InformationBreakers and fuses protect the wires to prevent fire. The 100 Amp breaker in the meter base (main) protects the wire from the meter base to the breaker panel. The 50 Amp breaker in the breaker panel protects the wire from the breaker panel to the outlet. Sometimes the 100 amp main breaker is located in the panel.If you are asking "Can you use two 50 amp breakers for the main breakers with a 100 amp service, then yes you can. The National Electrical Code allows you to use up to 6 breakers as the main overcurrent protection.
No, each size service needs its own meter base.
Minimum size is 10 gauge with a 30 amp breaker. To be safe I would install an 8 gauge with a 40 amp breaker.
The breaker will have a black wire connected to it. Turn off the main breaker and then disconnect that black wire from the breaker. The breaker will snap into the main bar. Remove the breaker and install the new one. Reconnect the black wire to the breaker and then install the cover and turn the main breaker back on.
Depends on the wire size you are using. If the generator breaker is a 30 amp then install a 30 amp breaker.
Depends on the size of the wire going to the A/C. If the wire is AWG #10 you cannot install a 40 amp breaker. If the wire is AWG #8 you can.
Yes.Additional InformationBreakers and fuses protect the wires to prevent fire. The 100 Amp breaker in the meter base (main) protects the wire from the meter base to the breaker panel. The 50 Amp breaker in the breaker panel protects the wire from the breaker panel to the outlet. Sometimes the 100 amp main breaker is located in the panel.If you are asking "Can you use two 50 amp breakers for the main breakers with a 100 amp service, then yes you can. The National Electrical Code allows you to use up to 6 breakers as the main overcurrent protection.
Not unless you change the wiring for that circuit. The breaker protects the wiring and if you install a 40 amp breaker on a 15 amp wire circuit you will have a fire in your home.
No, each size service needs its own meter base.
Minimum size is 10 gauge with a 30 amp breaker. To be safe I would install an 8 gauge with a 40 amp breaker.
The breaker will have a black wire connected to it. Turn off the main breaker and then disconnect that black wire from the breaker. The breaker will snap into the main bar. Remove the breaker and install the new one. Reconnect the black wire to the breaker and then install the cover and turn the main breaker back on.
No, you should not install a 30 amp circuit breaker to a machine which normally requires a 20 amp supply. The circuit breaker is protecting the wire to the machine. That wire is likely only rated for 20 amps, (# 12 awg). Therefore, a 30 amp breaker could allow too much current to go through the wiring to the machine and cause the wire to burn down. Replace the 3 phase 20 amp breaker with the same amperage breaker.
50 amp breaker.
You need a breaker rated for 10 amps and 250 volts. The breaker must also fit properly in your panel.
Normally older ovens required a AWG #8 wire on a 40 amp breaker. On a modern double oven I would recommend you install AWG #6 on a 50 amp breaker. That way you are safe and will not have to worry about the breaker tripping. It will cost a little more but is worth it in the long run.
If the 12,000 BTU A/C only requires 20 amps to run then yes you can use the same 12 gauge wire but you cannot change it to a 15 amp breaker. You will need to install a 20 amp double pole breaker. If it requires more than 20 amps you will have to replace the wiring and breaker.