0
What else can I help you with?
How can I remove a dome light fixture?
To remove a dome light fixture, first turn off the power to the fixture. Then, carefully remove the screws or clips holding the fixture in place. Gently pull the fixture down from the ceiling, being mindful of any wires connected to it. Disconnect the wires, and the fixture should come off easily.
Why wont the interior light come on in my 2004 dodgedurango?
it is obviously broken. you'll need a new light fixture
Can I have 120 volts at the light fixture but the light won't turn on I have checked the wiring and changed the light?
If you have 120 v at the wires connecting to the light fixture the light should come on. Its possible the voltage is not getting to the inside of the socket. Carefully measure the voltage between the metal blip at the bottom of the socket and the metal along the sides. Be careful here. Its tight quarters and easy for the voltmeter leads to touch the wrong things. Before doing that I would try a third light bulb. I've gotten them bad right out of the package. If you have voltage inside the socket, then for some reason the light bulb is not screwing far enough down so the bottom touches that metal blip on the bottom of the socket. If you don't have voltage inside the socket then that's your problem and you'll need a new socket.
How do you change the high mount brake light bulb on 2004 Honda Pilot?
Hi, I just changed the whole fixture for the third light. There are two caps on each side of the fixture. With flat screw driver, take off the caps and take out the screws. The light fixture will come out and twist the socket of the light bulb. Now you can able to change the light bulb. I hope this will help you all.
Why your new light fixtures dont come on when you have 120V at the socket?
My first suspicion is you have a loose or disconnected neutral. TURN THE BREAKER OFF WHEN CHECKING THE CONNECTION. To include all points, even the obvious, make sure you have changed the lamps to known working lamps from another fixture. How do you know it has 120 volts at the socket? If you tested it with a voltage tester or a multimeter, which wires were you connected to? In order to troubleshoot you need to make three measurements, at the BOXif wall or ceiling mounted or RECEPTACLE if plugged in with a cord, not the fixture socket the lamp screws into. Hot to ground (volts AC) Should be 120 volts nominal. This can vary from about 110-130v. Hot to neutral (volts AC) Should be 120 volts nominal. Neutral to Ground (volts AC) Should be 0 volts. These wires are electrically joined at your main panel. If you have 120v hot to neutral, your circuit is working properly. Any problem will lie in the fixture or the connections to the fixture. If you do not have 120v to neutral but you do have 120v hot to ground, your neutral is not connected. TURN THE BREAKER OFF and check the connection. If you do not have 120v to neutral or120v to ground, your hot is not connected. TURN THE BREAKER OFF and check the connection. If you have anything other than 0 volts neutral to ground, your fixture connection may be okay, but your neutral is not connected properly going back to the main panel. This is a dangerous situation, and it can result in fire over time. In this case have an electrician inspect the situation immediately!
Do recessed light kits come with the trim?
Yes. Recessed lights consist of two parts, the trim and the housing. The housing is the light fixture that is installed in the ceiling, and the trim is the light itself.
Do light fittings need to be earthed?
Normally the fixtures come with a grounding screw that you attach the grounding wire to. If the box you attaching the fixture to is metal and there is no grounding wire present then the grounded conduit should ground you fixture.
What is the output of a light ballast?
Fluorescent electronic ballasts have a voltage to amperage ratio chart on their face. Use this chart by selecting the voltage you are using and the corresponding amperage, then multiply the two numbers together for your wattage. Some fixtures come with more than one ballast, so you will need to take the wattage of all applicable ballasts for any given fixture to obtain the total wattage for the fixture.
What are the best light fixture options for a ceiling fan?
The best light fixture options for a ceiling fan are typically integrated light kits that come with the fan, or compatible light kits that can be added later. These can include options like LED lights for energy efficiency, dimmable lights for adjustable brightness, and stylish designs to complement the fan's aesthetics.
What are some stylish and energy-efficient options for replacing the globe on my ceiling light fixture?
Some stylish and energy-efficient options for replacing the globe on your ceiling light fixture include LED light bulbs, pendant lights, and flush mount fixtures. LED light bulbs are energy-efficient and come in various styles to match your decor. Pendant lights are a stylish option that can add a modern touch to your space. Flush mount fixtures are another energy-efficient choice that provides a sleek and contemporary look to your ceiling light fixture.
Why would the generator light come on in a 1979 corvette when the volt meter indicates charging at fourteen volts or higher?
Check pigtail connection at alternator (possible loose), or voltage regulator going out in alternator, take to autozone or other and have tested, replace.
Which type of lighting is best for a bathroom ceiling?
The best lighting for a bathroom ceiling is a hanging light fixture with more than one bulb. You don't want all of the light in your bathroom to come from a single bulb.
