Want this question answered?
Bad connections in the outlet or connector screws or it's feed connections at another oulet. Next time it quits bang on it and bang on the adjoining outlets. If one point causes a flicker - look for the problem there.
Just firmly connect the wires under the screws and that will couple them. Each outlet has two hot and two neutral screws; just connect the wires appropriately and make certain that the outlet is properly grounded.
Most switched outlets have one half that's hot all the time. If that's the case it will be as easy as changeing the outlet. In the center of each side of the outlet there is a small piece of copper connecting the two screws. Look and see if the copper piece is broken on the hot side, if it is then replace the outlet using the constant hot. Cap off the unused wire from the switch. If both sides of the outlet are switched then you can remove the two wires from the switch and tie them together. then either replace the switch and have a dummy or put on a blank cover. You should be all set.
I'm first off assuming this is a brand new plug, not a replacement. Okay. Ground first(green). Make sure you've got enough bare copper to wrap around the bottom screw. Then, strip and wrap the white around either of the silver screws on the side of the outlet. Finally, connect the black to the hot side (brass colored screws). And you should be all set.
Guessing you are replaceing an outlet? Black goes on the copper colored terminal and white on the same side that has the ground terminal. If you have checked and made sure that white is in fact the neutral you can run a jump wire from the side terminal to the ground. This will ground whatever you plug into the outlet as long as it has a 3 prong plug.
Remove the electrical connector from the old resistor. Remove the screws holding the resistor in place. Remove the old resistor. Put in the new one and screw in the screws. Attach the electrical connector.
Removing the back seat in the Kia Rio is simple. Remove the screws or bolts from the lower cushion and remove cushion. Then remove the now visible screws and remove the remaining parts.
Remove the Toyota Camry headliner. The overhead console retaining screws will be visible. Remove the retaining screws and the console will come off.
Door Speakers: * Remove the door trim panel * Remove the speaker mounting screws * Pull out the speaker and disconnect the electrical connector from the speaker and remove the speaker Door Subwoofers: * Remove the subwoofer grille trim panel * Remove the door trim panel * Remove the 8 mounting screws from the front side of the subwoofer * Remove the single subwoofer retaining screw from the backside of the subwoofer enclosure * Pull out the subwoofer,disconnect the electrical connector and remove the subwoofer Quarter Panel Speakers: * Remove the quarter panel trim * Remove the 4 speaker mounting screws * Pull out the speaker,disconnect the electrical connector and remove the speaker Parcel Shelf Speakers: * Working from inside the trunk area,disconnect the speaker electrical connector * Remove the parcel shelf * Remove the speaker mounting screws and remove the speaker
You have to remove the chrome bezel and possibly the grill depending on the model.
It is not difficult. First you have to remove the 12vot cigarette lighter plastic and then remove the radio. 4 screws for the radio. Then you have to remove the panel that goes from the radio up to the instrument cluster. This panel has 4 screws. 2 of them are on top of the instrument cluster (visible) and the other two should be visible after removal of radio.
Usually the screws are 6-32 oval head. Length 1/2 inch.
# Remove the door trim panel # Remove the mounting screws withdraw the speaker unplug the electrical connector and remove the speaker
Remove the air filter housing by removing 3 screws and pulling up. Remove the air filter. Remove two screws holding the reservoir and pull up. Disconnect the electrical fitting and hoses. You're done.
It screws into the exhaust and plugs into the electrical harness.It screws into the exhaust and plugs into the electrical harness.
You first empty the glove box. Next you remove the pins holding the glove box and snap it out. The screws are now visible loosen and remove the matrix.
Only 1 screw is visible, there are 2. Remove front sight hood, drive dove tail blade out from left to right. The other screw is visible now. Remove both screws and the ramp comes off.