answersLogoWhite

0


Best Answer

High-powered explosives.

User Avatar

Wiki User

โˆ™ 2009-02-19 23:42:40
This answer is:
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do remove the ignition switch on 1978 Chevy truck?
Write your answer...
Submit
Related questions

How do you remove the ignition switch cylinder to replace it on a 1971 Chevy truck with no key?

With no key you will have to drill out the existing tumbler assembly from the switch in order to unscrew the ignition switch bezel.


How do you replace the ignition switch on a 1985 Chevy truck?

replace ighnition switch for 1985 chevlot


How doi remove ignition without key from 1986 Toyota pickup truck?

Begin by removing the retaining ring at the top of your 1986 Toyota pickup truck ignition switch. The ignition switch will slide out. Remove the wiring harness from the back of the ignition switch.


Wiring diagram for ignition switch for 1974 Chevy truck?

Ignition wiring diagram


How do you remove and repair replace an ignition switch in 1996 1500 series Chevy truck that sticks in the off position?

call a lock smith .


How do you remove an ignition switch from a 1979 Chevrolet C10 pickup?

Remove the retaining ring from the top of your 1979 Chevrolet C 10 pickup truck ignition switch. Slide the ignition switch out and remove the wiring harness.


How do you change the ignition switch on an 87 Chevy C-10 pickup truck?

you have to remove the steering wheel, after that you need a tool to releave the tenison on the plate that looks like a sun there is a clip to remove. after that if you look where the switch is you will see a screw, if you remove it the switch will come out.


How to replace 1996 1500 Chevy truck ignition switch?

if tis like a 1995 you need to remove the lower dash panel below the column, the culoumn sleeve that is held on by 2 torx scres from the bottom, then you need a inverted torx sicket to remove to that hold the top sleeve on the column then you can get to the ignition switch


How do you remove the ignition switch on a 1968 Chevy truck?

turn key to acc then stick a paper clip in the little hole in tumbler then turn counter clock wise there you go


How do you change the ignition switch on a 2004 gmc 1500 sierra truck?

how to remove cover to replace ignition lock cylinder and what type of tools do i need


How do you remove ignition cylinder from 1975 Chevy pickup?

You will need to remove the retaining ring from the top of your 1975 Chevrolet pickup truck ignition cylinder. Slide the ignition cylinder out and remove the wiring harness. Reverse the process to install the new ignition cylinder.


Will a bad ignition switch shut down the electrical system on a 1994 Chevy truck?

A bad ignition switch can shut down a vehicle's electrical system. Ignition switches have been the cause of a major recall by General Motors.


How do you remove the ignition lock cylinder on a 1964 Chevy puck up truck?

Turn it, then pull up and out.


How do you remove a ignition key tumbler in a 1977 Chevy pickup?

Remove the retaining ring from the top of your 1977 Chevrolet pickup truck ignition key tumbler. Slide the ignition key tumbler out. Remove the wiring harness from the end of the key tumbler.


How do you remove ignition switch 1966 ford truck?

remove the silver ring that is on the dash buy turning it with channel locks, it should be threaded


How do you remove the ignition switch cylinder to replace it on a 1976 Chevy truck?

Remove the steering wheel then the lock plate then the turn signal switch. You will then see a screw close to the side of the lock cylinder. Remove this screw and pull the lock cylinder out. It takes a special tool to remove the lock plate and you can rent then at some parts stores although they aren't very costly.


How do you replace an ignition switch on a 1987 Chevy truck?

you have to pull the steering wheel off and then you will see a steel plate there push down on the steel plate and remove the snap ring that holds the plate in place. remove the plate and then remove the three Philips head screws that hold the plastic ring in place that is under the plate and pull the ring up and out of your way carefully. look in and you will see a torx head screw under the ignition switch remove that and the switch will come out. repeat steps to reinstall


How do you install ignition switch 1988 gmc truck?

You need to remove the steering wheel first with a puller. There is a latch you can trip with a small screwdriver that will let the ignition switch slide out. Simply replace the switch and put the steering wheel back on.


Can a Chevy truck with a 5.7 engine with a tbi cause detonation and pre-ignition?

can a chevy truck with a 350 engine with a tbi cause detonation and pre- ignition?


Where is the Inertia switch in a 2003 Chevy truck?

Chevy trucks do not have an Inerita switch. Only ford.


How do you disconnect the passenger airbag switch on a 97 Chevy truck?

insert ignition key into passenger airbag slot on the front dash and turn to off


Do you have to remove the steering column to replace the neutral switch in a 82 Chevy truck?

you dont HAVE to remove it but it does make it easier. removing the column it not very difficult.


How do you take a ignition switch off of a 1965 Chevy pick up truck?

The part that your key fits into has to be removed using a small paperclip to push through the hole you see near the key opening. The key switch will nee to be in a certain position, you push in the paper clp and the tumblers and all will come out. Now you remove the switch.


Chevy truck starts but wont turn off?

ignition switch wired wrong . wire from coil hooked to hot post instead of switched post


How do you remove the ignition switch on a 1992 Toyota Pickup Truck?

First, remove the lower dashboard panel in order to get at the switch. There are four Philips screws and one bolt that secures this panel. Then remove the two nuts and three bolts securing the steering column to the dash frame. This makes it easy to get at the switch. Remove the cover around the ignition switch. The front part is the key and lock tumbler, and the bottom is the electrical switch part that is not disturbed by this process. Take care not to pull the wires in the wire harness to the switch. Remove the key sensor switch from the housing that holds the tumbler and switch mechanism. Remove the screw that holds the ignition switch body. Remove the electrical harness part from the back of the switch. Then, insert the key and turn slightly. Release the pin under the tumbler casing and pull out the cylinder.