Want this question answered?
just pops off after removing the window handle, if manual, and some screws for the armrest and maybe the door trim side of window.
You have to remove the door trim on the inside of the door. Also remove the window crank handle if it is manual windows. 1. remove the window regulator by unbolting the regulator from the door shell and sliding the window guide arms out of the window channels. 2. You then remove either side or both sides of the vertical window channel that the window goes up and down on. 3. Finally, most of the time you need to remove the window rubber seal that runs horizontally along the bottom of the window opening to get the glass and the regulator channel that is attached to the glass out of the door.
Remove the trim pad by removing the door and window handles, then all of the screws you can find then the retainders around the sides and bottom of the door. Inside of the door is a lot of very sharp edges that can cut you bad also the reguoator is spring loaded. I suggest taking it to a trim shop.
Hello, this is straigh from the dodge repair manual. If you need pictures let me know John Roll window down. Remove window crank, if equipped. Remove screw attaching trim panel to outside mirror frame. Remove screws attaching pull cup to door. Using a trim panel removal tool, disengage clips around perimeter of trim panel, attaching trim panel to door. While holding bottom of trim panel away from door, simultaneously lift upward and inboard. Disengage power mirror switch connector, if equipped. Disengage power window/lock switch connectors from switch panel, if equipped. Separate trim panel from door. Remove door trim panel . Peel waterdam away from adhesive around perimeter of inner door panel Remove the door waterdam . Remove nuts attaching door glass to window regulator. Remove glass from door or move glass to full up position and secure glass to door with tape. Disengage power window motor wire connector from door harness, if equipped. Remove bolts attaching window regulator to inner door panel. Separate window regulator from door panel. Extract window regulator through access hole in inner door panel.
Remove the front door trim panel. Remove the front window trim. Unplug the power mirror. Remove the access hole cover. Finally, remove the nuts holding the mirror to the door frame.
Remove the door bezel.Remove the window switch.Remove the door pull trim bezel.Remove the 2 7MM bolts behind the door pull trim bezel.Using a door panel tool, you should be able to remove the plastic clips behind the door panel.
The process for removing the door panel can be found at: http://www.bodyshopzone.com/archives/trim/door_panels/Chevy/Equinox_2005/dp_front_rear.html
It is in the door. I suggest you take it to a trim shop to have it replaced.
* On models with power door locks and/or power windows disconnect the negative battery cable.If equipped with Delco Loc 2 or Theftlock audio system make sure you have the activation code * On models with power door locks pry the power door lock switch out of the door trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with power windows pry the power window switch out of the trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with manually-operated windows remove the window regulator handle * Remove the trim panel screws * Once all of the screws are removed detach the trim panel from the door disconnect any electrical connectors and remove the trim panel from the vehicle by lifting it up and away from the door
* On models with power door locks and/or power windows disconnect the negative battery cable.If equipped with Delco Loc 2 or Theftlock audio system make sure you have the activation code * On models with power door locks pry the power door lock switch out of the door trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with power windows pry the power window switch out of the trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with manually-operated windows remove the window regulator handle * Remove the trim panel screws * Once all of the screws are removed detach the trim panel from the door disconnect any electrical connectors and remove the trim panel from the vehicle by lifting it up and away from the door
* On models with power door locks and/or power windows disconnect the negative battery cable.If equipped with Delco Loc 2 or Theftlock audio system make sure you have the activation code * On models with power door locks pry the power door lock switch out of the door trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with power windows pry the power window switch out of the trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with manually-operated windows remove the window regulator handle * Remove the trim panel screws * Once all of the screws are removed detach the trim panel from the door disconnect any electrical connectors and remove the trim panel from the vehicle by lifting it up and away from the door
* On models with power door locks and/or power windows disconnect the negative battery cable.If equipped with Delco Loc 2 or Theftlock audio system make sure you have the activation code * On models with power door locks pry the power door lock switch out of the door trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with power windows pry the power window switch out of the trim panel with a flat-blade screwdriver unplug the electrical connector from the switch and remove the switch * On models with manually-operated windows remove the window regulator handle * Remove the trim panel screws * Once all of the screws are removed detach the trim panel from the door disconnect any electrical connectors and remove the trim panel from the vehicle by lifting it up and away from the door