answersLogoWhite

0

Best left to a trained gunsmith.

User Avatar

Wiki User

13y ago

What else can I help you with?

Related Questions

How do you adjust a trigger on a Remington 799 rifle?

Type your answer here... how do I adjust the trigger on Remington 799


How do you adjust the trigger on a Model 798 rifle?

Best left to a qualified gunsmith.


How do you adjust Winchester rifle model 43 trigger pull?

Do not attempt this. Have it done by a gunmsith.


What is a double trigger rifle?

If you are referring to a "SET Trigger" on a rifle. The Set Trigger releases all the normal mechanisms in the action but does not release the hammer on the rifle, but it sets up the firing trigger to act like a "Hair Trigger" just barley touch the firing trigger and the rifle goes off. It's used in hunting. It is common on black powder "Hawkins Rifles."


How do you adjust trigger pull on a Crosman phantom pellet rifle?

See the link below for the Owners Manual. Read the section "Adjusting the Trigger."


How do you adjust the trigger on a model 700 Remington?

It is very easy to adjust the trigger on a Model 700 Remington. Remove the rifle from the stock and there is 3 small screws you can adjust. One is for the lbs. of trigger pull, which be careful you don't make it so easy it's a hair trigger and could go off just by the jar from closing the bolt. The other is to adjust the length of trigger pull.


How does the double trigger on a JG Anschutz 22 rifle work?

Rear trigger is "set" trigger, by pulling it 1st, it makes the main trigger a "hair" or lighter trigger


How does one adjust the trigger pull on an Iver Johnson 22 Model X rifle?

To adjust the trigger pull on an Iver Johnson 22 Model X rifle, first ensure the rifle is unloaded and safe to handle. Locate the trigger adjustment screw, typically found at the rear of the trigger assembly. Turning the screw clockwise generally increases the pull weight, while counterclockwise decreases it. Make small adjustments and test the trigger after each change to achieve the desired feel.


What function does the double trigger on a rifle have?

On some of the older rifles, they had a set trigger. You would pull it first to set the other trigger. The second trigger would be a hair trigger. It would have a very light pull. The first trigger was supposed to keep from accidentally firing the rifle as you were aquiring the target.


How do you adjust trigger pull on ruger ranch rifle caliber .223?

Best left to a trained factory representative.


How do you adjust the trigger on a Model 70 rifle?

First, for liability reasons I have to tell you that only a qualified gunsmith should adjust a triger. That being said a 70 trigger is rather easy to adjust. 1. Check and double check that your rifle is unloaded. 2. Remove three bolts holding action to stock and separate the two. You will now see the trigger assembly. 3. There is a threaded screw through the rear of the trigger with a jam nut at the trigger. This screw and nut adjust the trigger overtravel, be careful you can adjust this too tight and not be able to pull the trigger at all. 4. Further down the same screw is two more jam nuts and a spring. Loosen or tighten these nuts to adjust the trigger pull to your liking. 5. For extra peace of mind you may want to put some nail polish on the screw and nuts to keep them in place. DO NOT USE LOCTITE it may seize the tiny nuts permantly. 6. Reassemble the action to the stock and tighted the three screws. The front screw and the rear screw should be 65 INCH POUNDS and the middle screw should be just snug(over tightening the middle screw will cause the bolt to bind) I use a little loctite on this screw so it can be left looser. 7. Prior to using the rifle test the trigger weight. WARNING be sure the gun is unloaded and the safety off. Now butt down the rifle and be sure the trigger is not light enough to cause the rifle to fire.


How do you adjust the trigger on a model 270 browning rifle?

Best left to a factory trained person, otherwise, you void your warranty.