0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is difference between servo and VFD?
A servo system is a closed-loop motion control system usually consisting of a motor (servo motor) usually a synchronous motor combined with an encoder for position/speed feedback, and a drive (servo drive) which is the electronic amplifier. A servo drive usually has some advanced functionality, like PLCopen commands, custom accel/decel ramps, compensation, and provides an interface for synchronization with the control system and other drives. A servo is a VFD, in that it probably uses triacs to control the output waveform that drives the motor; by varying the frequency and magnitude, it can precisely control the motor with closed-loop feedback of position/velocity from the encoder.A VFD (Variable Frequency Drive, also known as a Variable Frequency Inverter) generally refers to the electronic amplifier of an open-loop system, which can vary the frequency and magnitude to control speed. Without closed-loop control it will not be as precise as a servo system, but is usually good enough for most applications and will probably provide soft-start functionality and other protections to the motor.See also What_is_the_difference_between_servo_drive_and_variable_frequency_drive
What is servo motor in steam turbine?
it controls the over pressure of the water
What is the difference between servo motor and dc motor?
DC motor : -DC (Direct Current) Motors are two wire (power & ground), continuous rotation motors. -The speed of DC motors is controlled using pulse width modulation (PWM), a technique of rapidly pulsing the power on and off. The percentage of time spent cycling the on/off ratio determines the speed of the motor, e.g. if the power is cycled at 50% (half on, half off), then the motor will spin at half the speed of 100% (fully on). Each pulse is so rapid that the motor appears to be continuously spinning with no stuttering. Servo Motor : -Servo motors are generally an assembly of four things: a DC motor, a gearing set, a control circuit and a position-sensor (usually a potentiometer). -The position of servo motors can be controlled more precisely than those of standard DC motors, and they usually have three wires (power, ground &). Power to servo motors is constantly applied, with the servo control circuit regulating the draw to drive the motor. -PWM is used for the control signal of servo motors. However, unlike DC motors it's the duration of the positive pulse that determines the position, rather than speed, of the servo shaft.
What is the working principle of three phase servo motor?
Applied with PM servo motor. Because of power generation effect when stops, it is easier to brake. (Rotator: PM Stator: Windings) The magnetic force is be made by permanent magnet and the current is used to generate torque. Then high torque and efficiency are available at low current and small size. It has no brush so there is little noise/vibration and no dirt. And high precision control is available with high resolution encoder. A Servo motor Based on the design of conventional AC Synchronous motor, with addition of an Amplifier and a feedback device.
What is servo motor What are its applications in modern technology?
A servo mechanism is one where there is a control system, and actuator; and where there is feedback from the actuator to provide agreement with the control signal. The cruise control on your car is a servo system, for it senses the actuator's effect (road speed) and sends back a signal to the accelerator to adjust the car speed to the set target. Early servo mechanisms (but not the earliest) used an electrical motor, which was also able to send back information on its position. This feedback is the essential part of a servo mechanism. Probably the origin of the word is allied to "servant".
What is servo drive?
A servo drive is any motor controller which uses a closed feedback loop to monitor the motors speed. This is normally accomplished through the use of an encoder or resolver.
What you mean by servo in servo motor?
The servo motor is a type of motor which acts according to the command of the user. which serves the purpose of the user. therefore it is called as "servo" motor
What is a encoder motor?
An encoder motor is the part that engages the change between 4wd and 2wd.
Is it possible to control an electric motor with a servo or servo connector?
NO
Is a stepper motor with feedback loop a servo motor?
No, stepper and servo motor are by mechanical design two different types of motors.
What is hydraulic ram servo?
A hydraulic piston is also known as a servo or a motor.
How do you change encoder motor on a 2001 blazer?
hi this is peter i have a 2001 chevy blazer and how do i change the encoder motor on the transfer case? thanks
What is the application of servo motor?
Servo motors are used for precision motion control application.
What is a continuous servo?
A modified servo motor allowed to spin around with an unlimited range.
Where is encoder motor sensor for a 1999 Chevy Suburban?
The encoder motor sensor is found inside the front of the transfer case. The sensor motor assembly is removed with 3 - 15mm bolts after the front driveshaft and electrical connector are disconnected. The encoder motor sensor is under the big gear on the back of that assembly plate.
What type of motor is used for a robot arm joint?
servo motor
Why encoder is coupled with motor shaft?
Encoder is being used to measurethe depth of pile in case of piling rig
