answersLogoWhite

0

Remove wheel by wheel and rock the car to avoid slipping ( use jack stands for safety ) then you will find in the back of the caliper a bolt (bleed nipple) covered with small rubber cover, remove cover and start the engine, in this part you need assistance to press on the brake pedal many times (4 times pressing to the last then release), you have to be ready to untighten this bolt (bleed nipple) then ask your assistant to press full down and keep (DONT RELEASE THE PEDAL), once he pressed untighten the bolt (bleed nipple) but not too much, once the oil is out ( you have to put a container under this part) tighten it agin and ask your assistant to release the pedal, its better to do the four wheels to get the best performance and check the oil level before and after. Good luck

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

Where do you check brake fluid in 2002 Lincoln ls?

Where is the reservoir for the brake fluid


What makes the brake pedal spongy in a 2002 Chevrolet Suburban?

Air in the brake system. Bleed the brakes again.


Where are the bleed screws on a 2002 Isuzu Trooper?

On a 2002 Isuzu Trooper, the bleed screws are located on the brake calipers and the brake master cylinder. For the front brakes, you will find the bleed screws on the top of each caliper. For the rear brakes, the bleed screws are typically located on the rear brake cylinders. Always ensure you have the correct tools and follow proper procedures when bleeding the brakes.


How do you bleed rear brake drums for a 2002 Taurus?

Jack up, remove rear wheel, remove emergency brake cable, loosen bleeder valve and bleed as normal.


What brake fluid does 2002 Lincoln Continental need?

DOT 3 brake fluid ( if DOT 3 is not available , DOT 4 can be used according to the 2002 Lincoln Continental Owner Guide )


How do you bleed the fuel system in a 2002 eclipse gs 2.4L automatic?

If This Is To Remove Air From Fuel Lines. Forget It. You Do Not Have To Bleed The Fuel Line.


How do you change an abs brake module on a 2002 avalanche?

To change the ABS brake module on a 2002 Chevrolet Avalanche, first disconnect the negative battery cable to ensure safety. Remove the brake lines from the ABS module, taking care to catch any fluid spills and use a line wrench to prevent rounding the fittings. Unbolt the module from its mounting bracket and replace it with the new module, then reconnect the brake lines and reattach the battery cable. Finally, bleed the brake system to remove any air before testing the brakes.


How do you fix brakes on 2002 Isuzu Rodeo?

To fix brakes on a 2002 Isuzu Rodeo, first, ensure the vehicle is safely elevated and secure it on jack stands. Inspect the brake pads and rotors for wear; replace them if necessary. If the brake fluid is low or contaminated, bleed the brake lines and refill with the appropriate brake fluid. Finally, check for any leaks in the braking system and ensure the brake calipers and hoses are in good condition before reassembling everything.


Do you have to bleed all the brakes if you only change one brake line on a 2002 dodge grand caravan?

Always best to bleed both sides if you change a brake line. EG: Both front or both rear.


How do you change master cylinder 2002 ford windstar?

To change the master cylinder on a 2002 Ford Windstar, first, ensure the vehicle is on a level surface and disconnect the negative battery terminal. Remove the brake fluid from the reservoir, then unbolt the master cylinder from the brake booster. Disconnect the brake lines carefully, and remove the old master cylinder. Install the new master cylinder by reversing the steps, ensuring to bleed the brake system to eliminate any air.


What does the anti-brake symbol on a 2002 Lincoln LS look like?

On a 2002 Lincoln LS : The Antilock Brake System warning light is displayed in the tachometer It is near the number " 7 " The warning light shows ( ABS ) with a circle around the letters ABS


On a 2002 1500 HD should the brake pedal go to the floor when the truck isn't running?

no! you have air in the brake system or there is no pressure for some reason. look for leaks. bleed the system.