answersLogoWhite

0


Best Answer

TAKEDOWN FOR CLEANING Before you start, be absolutely certain that the pistol is unloaded by following the unloading instruction on page 5. Never work on a loaded firearm. It is not necessary to disassemble the .380 D.A.O. to clean and lubricate, This can be done by pulling the slide back all the way to the rear position, then run a cleaning rod with a solvent coated patch through bore and chamber, then run a clean, dry patch through until clean. Oil slide rails and outside diameter of barrel where it rides in frontof the slide. If it becomes necessary to disassemble for cleaning the procedures are as follows - j, Remove bolt pin with a 1/8" diameter punch, pull slide back approximately 1/2" so firing pin and spring will come out of bolt, then remove bolt by inserting a brass or aluminum rod into magazine well and drive bolt out of slide. 2, Slide will come forward off of frame, no other disassembly is necessary. RE-ASSEMBL V Replace recoil rod and spring into recoil rod hole in frame. Insert front of recoil spring into spring hole at front of slide. Pull slide back over the barrel, then down and back. Pull slide back slightly, approximately 1/4", so bolt can be inserted into top of slide. 5 L Drive bolt back into slide until retaining pin holes in side and bolt are aligned. (Use a soft face hammer to avoid damaging top of bolt or slide). 6, Replace firing pin and spring, push forward and let hammer down to hold in place, make sure RECESS in firing pin is lined up looking through retaining pin hole. 7, Replace bolt retaining pin. 8, Check for proper functioning before loading. j, 2, 3, 4, CLEANING Frequency of cleaning depends upon the frequency of use of the pistol. Accumulation of powder fouling in the breech and chamber area may affect the functioning of the pistol causing jamming or misfiring. If either of these conditions develop, clean the pistol. Wear Safety Glasses and Ear Protection at all times when shooting

User Avatar

Wiki User

15y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you break down a AMT 380 automatic?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What year was this AMT backup?

Amt 380 backup #70100


Where can you find a clip for amt 380 pistol?

Try e-gunparts.com


Can you fire 380 auto rounds out of a AMT 380 9mm Kurz?

Yes. 9mm Kurz (or Cortos) is the European designation for .380 ACP. also called .380 Auto.


How much does a used amt backup 380 cost?

50-150 USD.


You have an AMT 380 backup Serial A62721 When was it made?

No known published sn data.


Can you find parts for an AMT 380 9mm Back Up pistol?

I need a trigger spring for an AMT 380 backup single action. It is a coil type spring. Part # 123780. If you know where please email me at msulli5429@aol.com Thanks


Where can you buy a firing pin for a 380 amt backup double action gun?

try numrich.com


What is a Good price for a amt 380?

If it is in really good shape, they usually sell for about $200-$300.


How can I find the value of this gun Amt 380 with pat pending on barrel?

Blue Book of Gun Values


Can you shoot 32 ammo in your amt 380?

No-- If you will GOOGLE .380 ACP and also GOOGLE .32 ACP. You can see the difference in specifications. First item each page "WIKI"


Is there a safety on the amt 380 9mm kurz?

Yes, there are three forms of safety mechanisms on the AMT 380 9mm Kurz. 1.) Typical Grip Safety that must be gripped/depressed in order to fire the pistol. 2.) Thumb safety in front of the left grip panel. Move it up for safe (visible white dot) or down to fire (visible red dot) 3.) The brain matter between your ears. :-)


What year was the 380 9mm kurz amt backup made?

Who cares? It's such a pathetic caliber anyways.