0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What is Id versus od size in copper fittings?
id means inside diameter, od means outside diameter, copper pipe and tubing is measured by the od, therefore the od the pipe or tubing will be the same as the id of the fitting
What is the technical difference between tube and pipe?
The primary difference between pipe and tubing is how the size is designated. Pipe is designated by a "Nominal Pipe Size" based upon the ID (inside diameter) of the most common wall thickness. Tubing is designated by the measured OD (outside diameter). For Example: A 3/4 inch iron pipe has an OD of 1.050 inches, while a 3/4 inch steel tube has an OD of 0.75 inches. The Copper industry calls all cooper tubular products "Tubes" but they designate a "Type". Each type has specified OD and ID dimensions The size of a tube is determined by it's OD and the thickness. The actual OD of a tube is just the same as it's nominal OD. A certain size of a tube will keep the same OD no mater what the thickness is. It is true for pipe except that the actual OD is larger than it's nominal OD. For example, for a 1" schedule 5s pipe, the actual OD is 1.315", the thickness is 0.065" and the ID is 1.185". When it's thickness is schedule xxs (0.358"), then it's ID is reduced to 0.599" while keeping it's OD. Furthermore, the actual OD of a pipe is just the same as it's nominal OD when the size is the same as or larger than 14" per ASME/ANSI B36.10/19 . Consequently, both the size of tube and pipe is measured by it's OD and the thickness. Actually tube is used when we need to transfer heat from its walls and we want this to be happen while in pipes we try to stop the heat transfer such as we use tubes in boilers because we make steam we need to transfer the heat while when we transport steam we use pipes because we wana save heat energy. 2: pipe can be thick according to formula d/t >10 while tube will must thin according to this formula. The Real Difference: Sorry to say; wrong! Pipe and tube is ever so simple. Pipes are used to transport something, and tubes to construct something; hence, tubes are defined by the od "outside diamater" and wt "wall thickness" (for construction stability), and pipes id inside diamater to allow a calculation for transportation viz., speed, volumes etc. (od = id + 2 * wt).
What is the weight of mild steel pipe OD 40mm and wall thickness 4mm?
=3.14 * (Diameter of pipe in Mtr. - wall thickness in Mtr. ) * Wall Thickness in Mtr. * 7850
How you can calculate the lay ratio of armour in electric cables?
armoured OD X 10 time and gain lay of armouring.
How do you find the bearing number of a ball bearing?
The bearing number can be checked out depends on the size of ID (Inner Diameter), OD (Outer Diameter) and H (Height) of this bearing.
How can you calculate the ID of a pipe?
Can you calculate the ID of a pipe when you have the OD to be 10.75" and the wall thickness to be 0.5"Depends on what you know about it. If you have the outer diameter and you know the wall thickness, then ID = OD-2 x wall thickness
How do I Find wall thickness of tube?
wall thickness of pipe is (OD - ID) /2
Why pipe NB is different with OD up to 12 inches?
Based on the NPS and schedule of a pipe, the pipe outside diameter (OD) and wall thickness can be obtained from reference tables such as those below, which are based on ASME standards B36.10M and B36.19M. For example, NPS 14 Sch 40 has an OD of 14 inches and a wall thickness of 0.437 inches. However the NPS and OD values are not always equal, which can create confusion.For NPS â…› to 12 inches, the NPS and OD values are different. For example, the OD of an NPS 12 pipe is actually 12.75 inches. To find the actual OD for each NPS value, refer to the tables below. (Note that for tubing, the size is always the actual OD.)For NPS 14 inches and up, the NPS and OD values are equal. In other words, an NPS 14 pipe is actually 14 inches OD.The reason for the discrepancy for NPS â…› to 12 inches is that these NPS values were originally set to give the same insidediameter (ID) based on wall thicknesses standard at the time. However, as the set of available wall thicknesses evolved, the ID changed and NPS became only indirectly related to ID and OD.For a given NPS, the OD stays fixed and the wall thickness increases with schedule. For a given schedule, the OD increases with NPS while the wall thickness stays constant or increases. Using equations and rules in ASME B31.3 Process Piping, it can be shown that pressure rating decreases with increasing NPS and constant schedule.[note 1]
How do you find cylinder ID when the OD is known?
There is no corelation between a cylinders ID to OD.
What is Id versus od size in copper fittings?
id means inside diameter, od means outside diameter, copper pipe and tubing is measured by the od, therefore the od the pipe or tubing will be the same as the id of the fitting
What is the diameter of an 8 inch pipe?
The inside diameter (ID) is 8 inches. The nominal pipe size (NPS) and outside diameter (OD) depend on the thickness of the walls of the pipe.
What is the technical difference between tube and pipe?
The primary difference between pipe and tubing is how the size is designated. Pipe is designated by a "Nominal Pipe Size" based upon the ID (inside diameter) of the most common wall thickness. Tubing is designated by the measured OD (outside diameter). For Example: A 3/4 inch iron pipe has an OD of 1.050 inches, while a 3/4 inch steel tube has an OD of 0.75 inches. The Copper industry calls all cooper tubular products "Tubes" but they designate a "Type". Each type has specified OD and ID dimensions The size of a tube is determined by it's OD and the thickness. The actual OD of a tube is just the same as it's nominal OD. A certain size of a tube will keep the same OD no mater what the thickness is. It is true for pipe except that the actual OD is larger than it's nominal OD. For example, for a 1" schedule 5s pipe, the actual OD is 1.315", the thickness is 0.065" and the ID is 1.185". When it's thickness is schedule xxs (0.358"), then it's ID is reduced to 0.599" while keeping it's OD. Furthermore, the actual OD of a pipe is just the same as it's nominal OD when the size is the same as or larger than 14" per ASME/ANSI B36.10/19 . Consequently, both the size of tube and pipe is measured by it's OD and the thickness. Actually tube is used when we need to transfer heat from its walls and we want this to be happen while in pipes we try to stop the heat transfer such as we use tubes in boilers because we make steam we need to transfer the heat while when we transport steam we use pipes because we wana save heat energy. 2: pipe can be thick according to formula d/t >10 while tube will must thin according to this formula. The Real Difference: Sorry to say; wrong! Pipe and tube is ever so simple. Pipes are used to transport something, and tubes to construct something; hence, tubes are defined by the od "outside diamater" and wt "wall thickness" (for construction stability), and pipes id inside diamater to allow a calculation for transportation viz., speed, volumes etc. (od = id + 2 * wt).
How can you get the weight for steel pipe?
assuming it's hollow. 10.68*ID*(OD-ID)
How od you calculate total magnification?
== == == == == ==
What is the weight of mild steel pipe OD 40mm and wall thickness 4mm?
=3.14 * (Diameter of pipe in Mtr. - wall thickness in Mtr. ) * Wall Thickness in Mtr. * 7850
What is the make up torque HT55 375 drill pipe?
it will vary by Tool Joint OD and ID. FYI 7"OD x ID 4" HT55 is 52,600 Ft lbs
What will be the weight of steel round of 559 mm OD and 11 mm thickness?
depends on the steel.
