0
Three-wire outlets are now obsolete so don't change anything on the appliance.
You should change the outlet to the correct 4-wire kind but it must be done correctly and safely. So don't attempt to do it if you don't know what you are doing.
Call in a licensed electrician to install a new circuit for you with the right sizes of circuit breakers, the right size of wiring, a GFCI if necessary and the right type of outlet to supply your new appliance which has a four prong cord.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Wiki User
∙ 14y ago
Wiki User
∙ 15y agoSee the related link for information. It shows a 3 and a 4 prong setup.
Add your answer:
Earn +20 pts
What is the most cost efficient and quick way to fix the problem if you have a stove that has a four-prong cord and an outlet that only takes three prongs?
buy a 3 prong cord and plug set at lowes or home depot and change the cord on the appliance.
How do you change the plug on your clothes dryer cord from three prong to four?
You have to go buy a new four prong chord, unscrew the base of the old chord, and switch them out.
Can you plug a three-prong dryer into a four-prong outlet or is there an adapter you should use?
You should install a four prong. The older ones were three prong and had no ground. An adaptor isn't made because it wouldn't fix the problem. You could make your own adaptor and cut the ground off with a pair of dykes, but don't.
What is wrong if you changed a four prong to a three prong and the dryer is not heating?
My question is WHY did you replace a four prong dryer plug with a three prong! 220 volt Electric dryers require two hot legs, a neutral and a system ground wire. Sounds as though you shunted one of the hots or the neutral. You need to install a four prong plug of the same configuration and wire it exactly as the original.
You are trying to change a 3 prong cord to a 4 prong your new dryer has two green cables attached to the inside of the dryer?
Dryer plug three to fourOpen up the electrical access panel on the back of the dryer. You will see a terminal block with three wires going into it from the plug cord assembly. A red and black and white are now connected to the terminal strip. Look at the position and colours of the existing 3 prong cord and how it is connected. Make a diagram. Coloured wires on the outside terminals white in the center. From the center wire terminal you will see a jumper strap that goes to the frame of the dryer. When installing the four prong plug this jumper is removed completely. The kit should have with it a grounding lug that connects to where the removed grounding strip attached to the frame of the dryer. This is the attachment point for the fourth green ground wire from the new dryer cord assembly.
What is the most cost efficient and quick way to fix the problem if you have a stove that has a four-prong cord and an outlet that only takes three prongs?
buy a 3 prong cord and plug set at lowes or home depot and change the cord on the appliance.
Who sells 8 ft 3 prong dryer cords?
Under the new electrical code rules three prong dryer cord receptacles and therefore cords are not allowed to be installed. As you are finding out, stores are not carrying them in stock any more. You should consider an upgrade for safety sakes, to a four prong plug cord and change the wall receptacle to a four prong receptacle. There are instructions on how to do this your self on Answers.
How do you change the plug on your clothes dryer cord from three prong to four?
You have to go buy a new four prong chord, unscrew the base of the old chord, and switch them out.
Can you plug a three-prong dryer into a four-prong outlet or is there an adapter you should use?
You should install a four prong. The older ones were three prong and had no ground. An adaptor isn't made because it wouldn't fix the problem. You could make your own adaptor and cut the ground off with a pair of dykes, but don't.
How do you hook up 4 prong cord to 3 prong dryer?
To adapt a three prong range cord?æto a four prong outlet you need to remove the screws from the back plate to open the electric access panel. Then, pull out the copper grounding strip attached to the middle terminal. Next, remove the green ground screw from under the terminal block and attach it to the four prong outlet.?æ
How do you connect two three prong outlet to four prong transfer switch?
There is not enough information stated as to what you are trying to do.
What is wrong if you changed a four prong to a three prong and the dryer is not heating?
My question is WHY did you replace a four prong dryer plug with a three prong! 220 volt Electric dryers require two hot legs, a neutral and a system ground wire. Sounds as though you shunted one of the hots or the neutral. You need to install a four prong plug of the same configuration and wire it exactly as the original.
You are trying to change a 3 prong cord to a 4 prong your new dryer has two green cables attached to the inside of the dryer?
Dryer plug three to fourOpen up the electrical access panel on the back of the dryer. You will see a terminal block with three wires going into it from the plug cord assembly. A red and black and white are now connected to the terminal strip. Look at the position and colours of the existing 3 prong cord and how it is connected. Make a diagram. Coloured wires on the outside terminals white in the center. From the center wire terminal you will see a jumper strap that goes to the frame of the dryer. When installing the four prong plug this jumper is removed completely. The kit should have with it a grounding lug that connects to where the removed grounding strip attached to the frame of the dryer. This is the attachment point for the fourth green ground wire from the new dryer cord assembly.
Are there 3 prong to 4 prong adapters for driers?
No, and adapters are not needed. What needs to be done in remove the old three blade dryer plug and install a new four blade cord on the dryer.Dryer plug three to fourInstructions should come with the new cord. Open up the electrical access panel on the back of the dryer. You will see a terminal block with three wires going into it from the plug cord assembly. A red and black and white are now connected to the terminal strip. Look at the position and colours of the existing 3 prong cord and how it is connected. Make a diagram. Coloured wires on the outside terminals white in the center. From the center wire terminal you will see a jumper strap that goes to the frame of the dryer. When installing the four prong plug this jumper is removed completely. The kit should have with it a grounding lug that connects to where the removed grounding strip attached to the frame of the dryer. This is the attachment point for the fourth green ground wire from the new dryer cord assembly.
Which Oxygen sensors do i order for Mazda millenia?
There are 3 prong and 2 prong sensors and depending on your year and model either three or four separate sensors.
Whats the term for a single prong on a fork?
Fork prongs are called tines.
When changing a three prong outlet on a dryer to a four prong where can you connect the ground?
Answer for USA, Canada and countries running a 60 Hertz supply service.Dryer plug three to fourInstructions should come with the new cord. Open up the electrical access panel on the back of the dryer. You will see a terminal block with three wires going into it from the plug cord assembly. A red and black and white are now connected to the terminal strip. Look at the position and colours of the existing 3 prong cord and how it is connected. Make a diagram. Coloured wires on the outside terminals white in the center. From the center wire terminal you will see a jumper strap that goes to the frame of the dryer. When installing the four prong plug this jumper is removed completely. The kit should have with it a grounding lug that connects to where the removed grounding strip attached to the frame of the dryer. This is the attachment point for the fourth green ground wire from the new dryer cord assembly.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energizedIF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
