Best Answer

There are two housings above the plate all you need is a Phillips head screw driver remove the 4 bolts and change the bulbs it's that easy

User Avatar

Wiki User

โˆ™ 2012-08-12 06:36:18
This answer is:
User Avatar
Study guides
See all Study Guides
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you change the license plate light bulb on Mazda protege?
Write your answer...
Related questions

Mazda Protege gas light?

reset it.

How do you replace the license plate light fuse for 1999 Mazda 626?

How do you change the liscence plate light fuse

Where is the fuse for the tail light aton a Mazda Protege?

Fuse panel.

What does a blinking Hold Light on a 1992 Mazda Protege mean?

tranny problems

How do you change the horn on a 1994 Mazda Protege?

remove passenger side signal front light first then passenger headlight and horn should be right behind below the side passenger signal light!

Where is the brake light switch for the 1997 Mazda protege?

Above the brake pedal,its black plastic.

How do you replace the license plate lights on a 1999 Mazda protege?

Open the trunk. Turn the socket counterclockwise and remove. Then gently pull out the light bulb. Place the new bulb in the socket and replace the socket into the lens by turning clockwise. Replacement light bulb #3652.

How do you you reset change oil light on a Mazda?

Reset the change oil light on Mazda 3

What does the hold light mean on a 1990 Mazda protege mean?

The HOLD light means you have an electrical problem with your transmission. See your mechanic ASAP.

If you have a Mazda Protege '91 which has a hold light blinking and the speedometer does not work what is wrong with it?

it could have a bad speed sensor

Does the check engine light on a 1998 Mazda Protege have a fuse?

It is run off of the same fuse as the engine computer.

Hold light blinking Mazda Protege?

To check the hold light blinking of a Mazda Protege, take off the plastic over the shifter tube or bar. Then take off the console below it and look at the wires that come up from the hollow center of the tube. The edge of the shifter tube may have cut through the wire insulation.

Can you troubleshoot the check engine light on a 1995 Mazda Protege?

Have vehicle scanned at auto parts store--most will do this free

Your brake light sw is working and your brake lights still remain on for your 1992 Mazda Protege?

Switch is defective or out of adjustment.

High mount brake light replacement Mazda protege 2001?

Remove the high mount brake light retaining screws from your Mazda Protg. Remove the high mount brake light wiring harness. Reverse the process to install your new high-mount brake light.

Why does the battery light stay on when a Mazda protege 1998 is running?

You have a problem with the charging system. More than likely the alternator has failed.

How much fuel is left in the gas tank of a 2000 Mazda Protege when the warning light comes on?

roughly 20 miles worth

What does od Alarm light on 2002 Mazda Protege mean?

The alarm warning light in your 2002 Mazda Protg is an indication that the alarm system is deactivated. Remove the alarm fuse, for 10 seconds. Put the fuse back into its original slot.

You have a 1992 Mazda Protege hold light remains on?

I suspect your hold switch on the shift lever might be bad..or ahs a broken wire.

What size is the fan belt on a 2003 Mazda protege 5?

you dont have strap on light cars just on pick-up's and big trucks

Why doesn't the spark plug spark on a 2002 Mazda protege?

car stalled at red light and will not start. there is no spark from spark plug, help!

How do you remove the tail light assembly on a 1997 Mazda Protege?

To remove the tail light assembly on a 1997 Mazda Protege remove the two screws that are usually covered by the trunk. After that use some force and push on the inner part of the tail light toward the side of the car. There is a clip in the side of the car that requires some force to undo. Make sure you push in the outward direction to either the driver side on the driver side tail light or the passenger side for the passenger side tail light. After that is removed the tail light should be hanging by wires ready for bulb changes. To change the bulbs just twisth the plastic part.

Why does the Mazda protege brake indicator light stay on?

Typically the light will remain on if the fluid is low, or maybe the ebrake just pulled just enough that it is on..... or the switch that is triggered by the handle is faulty

Where in fuse box is tail light fuse 1997 Mazda protege?

I think its on the driver side there should be a panel on the right hand side near the excellerator

Why when your Mazda Protege stops at a light the AC starts blowing warm?

It's due to your car not having freon go and get it charged. The cold air is from you driving!

People also asked

Where is the starter for Mazda Protege 1996?

View results