Not very much. As far as I am aware they are intercompatible, some sensitive equipment such as computers have 220/240 switch, but most equipment made for Europe is designed for 230v.
Short answer: No. (unless you like ruining motors) Longer answer: Not really, but there are some motors that can be re-wired so that instead of 440v they will run on 220v. However, this is not that common. Conclusion: Check the motor to see if it is dual-voltage on it's nameplate. If it is, you can re-connect it to work on 220v. If it is NOT a dual-voltage motor, you will absolutely ruin it if you connect it to 220v.
I have a sole F60 bought in US and I use it now in France with a transformer ; you never know if you can use it or not, sometimes it works , sometimes not...I don't know why maybe it's a problem of frequency...
If all the components are rated to 220V, yes. Keep in mind that if the appliance was designed for 110V it may arc if 220 is run through it. If you don't know the device can handle 220V, don't run it at 220V. Chances are it was manufactured cleaply and cannot handle the extra voltage.
Quick answer is that 220v does not use or need a neutral. The original concept of the neutral (going back to Edison and DC power) was cutting the power in half (not really accurate but one way to look at it). Think about two 110v batteries in series the neutral would come off the connection between the two batteries. so current flow would go from +110 to -110 (first battery) to +110 to -110 (second battery) resulting in 220 output. The connection between the batteries (the neutral) is +110 / -110 resulting in 0. If you want a 110 current instead of using the full flow you could instead use only 'one side' and the neutral and get the 110. When we made the move from DC to AC the basics of this format was kept. So for 110v you need hot and neutral (and a ground) for 220v you need two hots (no neutral) and a ground.HUGE CATCH - WARNING - WARNING!!!Just because you think your equipment is 220v doesn't mean everything it does it does requires 220v for example: some equipment uses 220v for the motor and 110v for the rest of its electrical needs (Dryers are a typical example). In the old days, the dryer would use the two hots (and ground for safety) for 220v and then use one hot and ground (no 'safety' ground) for 110v. However, people often got shocked because this unsafe method would often cause the entire metal chassis to take on a charge. So todays dryers (and any other machine that has both 220v and 110v components) have and are required to have 2 hots ground and neutral. However, the documentation isn't always specific about the '110v need' and a lot of 220v only equipment will still have 4 wire connections even though the neutral is not needed.If you are sure your equipment never utilizes 110v - then you don't need a neutral (a single motor, no thrills (control panel, laser guides, etc), 220v table saw would be fine with out a neutral (one with the thrills may be fine also - depends on the power requirement of the 'thrills'). I don't know about your generator is depends if it is strictly 220v.
nothing
Both screws are brass because in the US you need two hots to get 220V. In a 220V only circuit you do not connect the neutral, only two hots and a ground. This is why 220V breakers are twice as wide as 110V and have two terminals instead of one.
If you connect 110V xbox one to a 220V outlet, only the power supply will burn and not the Xbox one.
Typically, a 100 ohm resistor is used to connect a 1.5 volt led to a series 220v ac adapter. Many LEDs can be connected into a string using the resistors.
In a word; no. If you ever plan to have both groups of equipment running at the same time the panel will be constantly tripping. Also most "equipment" normally runs on 220v which requires two hots: both phases.
Short answer: No. (unless you like ruining motors) Longer answer: Not really, but there are some motors that can be re-wired so that instead of 440v they will run on 220v. However, this is not that common. Conclusion: Check the motor to see if it is dual-voltage on it's nameplate. If it is, you can re-connect it to work on 220v. If it is NOT a dual-voltage motor, you will absolutely ruin it if you connect it to 220v.
There may be a switch on the equipment to change the input voltage to 110v. Check near where the cord attached to the equipment you're using, it will be a recessed switch.
Yes it will. The only thing that you have to keep in mind is that in Angola the power is 220V so U'll need a power brick with 220v. Or U can buy a power converter to convert 220v to 110v.
Frequency doesn't come into it for normal electrical devices, as long as the voltage matches it will be fine. 50/60hz differences only really affect display equipment.
Not very much. As far as I am aware they are intercompatible, some sensitive equipment such as computers have 220/240 switch, but most equipment made for Europe is designed for 230v.
things... so kik] \
The ports used to connect external sound equipment are Line In, Mic and Line Out. These ports are usually located on the computer's sound card.