0
A Blue wire is normally the "Neutral" wire on a standard 230 Volt supply.
A Brown wire is normally the "Live" wire on a standard 230 Volt supply.
A Green/Yellow wire is normally the "Earth" or "Ground" wire.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
What else can I help you with?
Where does the blue wire connect on a ceiling fan?
The blue wire on a ceiling fan typically connects to the light kit or light fixture.
Where do you connect the light blue wire of a xplod stereo?
Light blue is for steering wheel controls or a wire remote control.
What is the blue overhead light on a 2007 Honda CR-V?
The blue light is just ambient night light. It serves no purpose other than to provide a little extra light in very dark conditions.
How do you wire a french light switch?
To wire a French light switch, first, ensure the power is turned off at the circuit breaker. Connect the live wire (usually brown) to one terminal of the switch and the wire going to the light fixture (also brown) to the other terminal. The neutral wire (typically blue) should be connected directly to the light fixture, without going through the switch. Finally, secure the switch in its box and restore power to test the installation.
What is the blue wire used for on a ceiling fan?
The blue wire on a ceiling fan is typically used to connect the fan's light kit.
What is the purpose of the blue wire on a ceiling fan?
The blue wire on a ceiling fan is typically used to connect the fan's light kit.
What is the purpose of the blue wire in a ceiling fan installation?
The purpose of the blue wire in a ceiling fan installation is to connect the light kit to the fan for controlling the light separately from the fan's motor.
How do you wire a 240 volt light fixture?
To wire a 240-volt light fixture, you'll need to ensure you have a dedicated circuit with a 240-volt power supply. You will connect the fixture's hot wire to one of the hot wires from the circuit, the neutral wire to the neutral wire, and the ground wire to the ground wire. It's crucial to follow the manufacturer's instructions and consult a licensed electrician if you're unsure.
What is the purpose of the blue wire in a ceiling fan?
The purpose of the blue wire in a ceiling fan is to connect the light kit to the fan's electrical system, allowing the light to be controlled separately from the fan's motor.
Why is the ski blue?
The blue color of the sky is due to Rayleigh scattering. As light moves through the atmosphere, most of the longer wavelengths pass straight through. Little of the red, orange and yellow light is affected by the air. However, much of the shorter wavelength light is absorbed by the gas molecules. The absorbed blue light is then radiated in different directions. It gets scattered all around the sky. Whichever direction you look, some of this scattered blue light reaches you. Since you see the blue light from everywhere overhead, the sky looks blue.
How do you connect a ceiling fan with white green black and blue wires on the ceiling fan?
Black wire goes to (line) which is 110v comming in to ceiling box from light switch. It will connect to either black or red, which ever they ran. White is neutral and connects to white in box. Blue is for the light kit if you are using one. You may also connect it to the black if you just use the chain to turn on light.
How do you connect a ceiling fan with white green black and blue wires one the ceiling fan?
This sounds like a ceiling fan that also has a light attached to it. The black and white wires are used for the incoming supply voltage. The green is the ground wire. The blue wire is most likely the wire that goes to the lamp portion of the ceiling fan. The black and blue wires are separated from each other in the fixture so that the fan motor and the light can be independently switched. In these types of installations a three wire cable is strung from the fan switch box to the fixture box.For independent switching, the junction box should be a two gang box. From the power source in the switch box, the white wires all connect together. The incoming black connects to the top of the two switches in the two gang box. Bottom of the first switch to the black in the three wire cable, Bottom of the second switch to the red wire of the three wire cable.At the fixture junction box, incoming white wire to the fan white wire. Incoming black wire to the fan black wire and incoming red wire to the fan blue wire. If wired this way the light and fan motor can be individually switched on and off.If there is only one switch box, at the fan junction point connect the black and blue wires together to the incoming black wire. White to white wires together and green wire to the ceiling junction boxes ground terminal. In this configuration the switch will turn on both the fan and light at the same time.
