0
To maintain the pressure of 1 bar in a pipeline you would normally employ a regulator which has a diaphragm which works a needle valve balanced against an adjustable spring. An example of the use of a regulator would be the ones found on propane cylinders to regulate the gas pressure.
What else can I help you with?
How do you calibrate a vacuum pressure transmitter?
To calibrate a vacuum pressure transmitter, first ensure it is connected to a known pressure source. Apply the vacuum pressure and compare the transmitter's output reading to the actual pressure. Make adjustments if necessary using the zero and span adjustments until the output matches the actual pressure value.
How can you determine the level of liquid without making any cintact with it using any probe?
By differential pressure of the liquid and the air gap above the liquid. Both the pressures are given to the differential pressure transmitter, and the signal received from the transmitter is then converted into level using conversion factors supplied by the supplier of the transmitter.
Do you have to reprogram a remote control transmitter for a 2000 Dodge Stratus after the battery has been changed?
You have to go to the dodge dealer and have them reprogram it using their scan tool.
How does a 3 way manifold valve work?
If you mean by three-valve manifold, then If you apply excessive pressure to your differential pressure transmitter, you could damage your instrument. This is known as over-ranging the transmitter. A three-way manifold valve is a device that prevents the instrument from being over-ranged. It also allows the isolation of the transmitter from the process loop (an option which could be used generaly for maintenance or re-calibration or fitting new equipment). It consists of two blocking valves and one equalizing valve. The blocking valves are for both high pressure and low pressure sides. During normal operation, the equalizing valve is closed and the blocking valves are open. When the transmitter is put into service, care should be taken to ensure that the high pressure is never applied to one side of the Differential Pressure Transmitter. To put a DPT into service using the Three-way manifold valve is to first close all valves. Then, open the equalizing valve to ensure the same pressure will be applied on both sides of the transmitter. Therefore you will have a zero differential pressure. Next, the high pressure block valve is opened slowly (to check for leakage from both sides of the transmitter). The equalizing valve is closed and this locks the pressure from both sides of the transmitter. Now open the low pressure block valve to apply the process pressure to the low pressure side and establish the working of the DPT.
Can I attach more than one device to IR transmitter?
Yes, you can attach multiple devices to an IR transmitter, but it depends on the specific model and its capabilities. Some IR transmitters are designed to control multiple devices simultaneously, while others may require a separate transmitter for each device. Additionally, if using a universal remote, it may be possible to program it to control multiple devices through a single IR transmitter. Always check the specifications and compatibility of your equipment before attempting to connect multiple devices.
What is Direct Pressure and Inderect pressure?
Direct pressure involves applying pressure directly to a wound to control bleeding, typically by using a clean cloth or bandage. Indirect pressure involves applying pressure to a pressure point near the wound to help control bleeding if direct pressure alone is not enough.
High range remote control using rf signal based on microcontroler?
try for 455mhz rf remote transmitter ,455 mhz remote controls are not available in the market
What is a wet leg?
Wet legs are used on differential pressure measurement where both sides are filled with liquid. Exception is level measurement in a pressurised vessel (boilers). Dry legs are used where the low side is exposed to atmosphere using a DP transmitter for level measurement in a open tank.
How do you set radio to use linear?
Depends on what exciter (transmitter, or transmitter part of a transceiver) you are using and what kind of linear you will be using. Generally, the transmitter part is 100 watts or less out to your linear. This is the RF (Radio Frequency) connection. The other connection is ALC (Automatic Limiting Control). This is a feedback connection from your linear to your exciter which controls the exciter to decrease power. The ALC hopefully will prevent over driving the linear so your signal will not be distorted. There can be other control cable/s which allow your exciter to control the linear's band (frequency) setting. This is just basic information and one must compare the equipment manuals or ask the manufacture of your equipment for advice.
How do you make a radio transmitter on the Sims 2 Castaway?
by getting a transmitter and radio. then you press make radio into a transmitter. the transmitter and radio are both by the airplane in areoplane jungle, the transmitter is annoyingly hard to find as it is too small to see. The radio is big, however, and you should spot it right away. also ig you do this try using the transmitter on the volano or in crystal caves...
When using a mouse what is the most common port used for the transmitter?
serial
Where can I find the the best FM transmitter?
From the research I have done, the best FM transmitter will depend on what you are using it for. Two that I found come rated with 4 and 1/2 stars are the Belkin TuneCast F8Z498-P FM Transmitter and the Griffin itrip auto fm transmitter for ipod.
