answersLogoWhite

0


Best Answer

As Microsoft Word is more leters and words it may not be the best way to do flowcharts in. If you choise to put a picture of a flowchart in Word then is should be a simple matter of copy and paste

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you copy a flowchart from the raptor program and paste it in a Microsoft word document?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Engineering

How do you make flowchart of ascending order using raptor?

Hey sunil i have an idea about mode that is more repeated data is mode ok na Example in the series 2,4,5,2,4,5,2,4,24,22,2,2,7,8,9,2 Mode for this data is 2 i.e. Answer is 2


How heavy is a raptor 660?

A raptor 660 is about 450lbs. When the raptor 700 came out, many found it to be much faster. Not only is this due to the extra displacement of the engine (668cc to 686cc) but they used an aluminum frame instead of a steel one, reducing the weight to 398lbs The front end on a 660 is realy light perfect for wheeles


Can a 400ex beat a 660 raptor?

no only if the raptor stayed stock and the 400ex had full exaughst, airfilter(no airbox lid), dyno jets, 440 big bore kit, and other mods


How can you declare global an local variables in flowcharts?

The simple answer is you don't. The primary purpose of a flowchart is to show the flow of execution through an algorithm, with all primary functions and decisions described in broad, abstract terms. There is no need to distinguish between local and global variables because that is an implementation detail -- it's far too low-level a concept for algorithm design. All variables utilised by an algorithm should essentially be declared up front at the start of the flowchart and should therefore be treated as being local to that particular flowchart. It doesn't matter where those variables came from, only that they be initialised accordingly. The decision to make a variable global comes much later, once the interactions between different flowcharts have been established. Even so, a global variable should only ever be considered when the variable represents a truly global concept. In the vast majority of cases, passing arguments into functions is often the better option. Especially when separate algorithms are intended to run concurrently because making a global variable thread-safe can seriously impact performance. But this is not a concern in algorithm design, they are only of importance to the implementers; the class designers.


Why was the f22 cancelled?

There have been several reports as to the F-22's overall mission ready rate and maintenance requirements.Lockheed-Martin's F-22 spokesman says that the overall mission ready rate has improved from 62% in 2004 to 68% in 2009, and is "on track" to reach 85% by the time the fleet reaches 100,000 flight hours.[173] The Washington Post says that between October 2008 and May 2009, just 55 percent of the deployed F-22 fleet has been available.[174] Air Force Magazine reported that the Washington Post article's was incorrect and that mission capable rates have been climbing, and by June 2009 stood at 62.9%, compared to approximately 70% for the mature F-15 and F-16 aircraft.[175][176] The Air Force Association states that the current mission capable rate for the entire F-22 fleet is 70%,[177] which is in line with the 71.2 percent the even newer Super Hornet managed on its first wartime deployment.[178]In July 2009, the Air Force reported that the F-22 requires more than 30 hours of maintenance for every flight hour, with the total cost per flight hour of $44,000.[174] The Office of the Secretary of Defense puts that figure at 34 hours of maintenance per single hour of flight at a cost of $49,808 per hour of flight. The Pentagon requirement is for 12 hours of maintenance per flight hour.The F-22 also reportedly encountered a critical failure every 1.7 hours.[N 2] The F-22 had required maintenance every 0.97 flight hours in 2004. This improved to 3.22 flight hours per maintenance event in production Lot 6 aircraft.The aircraft's radar-absorbing metallic skin is the principal cause of its maintenance troubles, with skin repairs accounting for more than half of the maintenance. Another source of maintenance problems is that many components require custom hand-fitting and are not interchangeable.[174] The canopy visibility has degraded more rapidly than expected, with refurbishments at 331 flight hours, on average, instead of the required 800 hours.[174] Pentagon officials respond that measuring flying costs for aircraft fleets that have not reached 100,000 flying hours is premature. They say improvements have been made since 2008, and the F-22s are on track to meet key performance parameters by 2010.[174]However, rain has caused "shorts and failures in sophisticated electrical components" when the Raptors were briefly posted to Guam.[180]Each Raptor requires a month-long packaged maintenance plan (PMP) after every 300 flight hours.[181]