0
How i can Convert the gray code 110111101 to binary code and design the circuit?
Wiki User
∙ 11y ago
first decide the numbar of bits...for four bits write the varoiurs combination of each bit.
for 4 bits 2^4=16 combination starting from 0000-1111.
similarly you will get 4 bit gray code by ex-oring (u may find this conversion in any book digital book).
now draw k-map for each out put bit
binary gray
0000 0000
0001 0001
0010 0011
...... ......
....... ......
1111 0000
consider case for 0010 to 0011.
lsb will be g0(1) and msb will be g3.(0)
each bit should be considered as an output and k-map has to be drawn for each output,viz g0,g1,g2,g3.
after implementing this ,realise the output expression using gates.(k map will give simplified output).
this is basic operation...but if u plan to implement in an project try getting an ready made IC.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Logic circuit that converts four digit Binary Input into Binary Coded Decimal?
Design a logic circuit that converts a four digit binary input to equivalent Binary Coded Decimal value. You need to first create the truth table (please note this circuit should have four input bits, but five output bits; for example, for an input 1001 (decimal 9) the suggested output will be 0 1001 (the BCD value 0 9); and for an input 1010 (decimal 10) the suggested output should be 1 0000 (the BCD value 1 0 )). After creating the truth table design the Boolean expressions for each of the five output bits. Draw the resulting circuit diagram using AND - OR - NOT gates.
How can you design a distribution board?
Design of a circuit board starts with a layout of what you require the circuit to do. Plug and component placement depend on where the board will be mounted and the environment that the board will be used in.
What is design current?
BS7671:2008, Requirements for Electrical Installations, defines the design current (of a circuit) as 'the magnitude of the current (rms value for a.c.) to be carried by the circuit in normal service'.
Design a combinational circuit that accepts a three bit number and generates a binary output equal to twice the input value?
There is no need for a combinatorial circuit to multiply a number by two. A binary number, left shifted one place, is twice the original binary number. The specific answer to the question is that you would connect the three input lines to the three high order output line of four output lines, and connect the low order bit of the four output lines to logic 0. If the three input lines were labelled A, B, and C, the output would be A, B, C, and 0.
How do you make a circuit so the lights can be turned on and off separatley?
To design a circuit so that lights can be turned on and off separately, we connect the circuit in parallel.
How do we design binary phase shift keying modulator with detail circuit?
circuit of modulation PSK
Logic circuit that converts four digit Binary Input into Binary Coded Decimal?
Design a logic circuit that converts a four digit binary input to equivalent Binary Coded Decimal value. You need to first create the truth table (please note this circuit should have four input bits, but five output bits; for example, for an input 1001 (decimal 9) the suggested output will be 0 1001 (the BCD value 0 9); and for an input 1010 (decimal 10) the suggested output should be 1 0000 (the BCD value 1 0 )). After creating the truth table design the Boolean expressions for each of the five output bits. Draw the resulting circuit diagram using AND - OR - NOT gates.
Where is binary used?
Most commonly, in computers. In general, any electronic circuit that deals with numbers (clocks, calculators, instruments, controllers, etc.) will use a binary representation, because circuits that switch between two states are easy to design and inexpensive to manufacture.
Design a Combinational circuit that has three input and one output the output is 1 when the binary value of the input is less than three the output is logic 0 otherwise?
If you are talking combinations, without binary number representations, then you are talking about a circuit that has a 1 output when any input is a 0. That is a 3 input NAND gate. If you are talking binary number representation, then you are talking about a circuit that has a 1 output when the inputs are 010, 001, or 000. Use a 3 to 8 decoder, with an OR gate on the low three outputs.
Can mechanical calculator used for octal number or binary number?
In theory, yes.In practice, you would have to change the mechanism from its decimal design to the octal or binary design.
Design and implementation of a buffer circuit using operational amplifier?
design and implementation of a buffer circuit using operational amplifier
How do you design an analog electronic circuit?
First you start with an idea of what the circuit will do.
How do you design circuit on PCB board?
I know the best circuit board design company which can design circuit board for you.PCBs are the backbone of electrical engineering. It is also known as brains of electronic devices. To create a PCB Design you need to draw holes, pads and wires for your circuit. Some steps of design a circuit board are as:a.Take a printout of circuit board layoutb.Cut the Copper Plate for the Circuit Boardc.Transfer the PCB Print onto the Copper Plated.Iron the Circuit from the Paper onto the PCB Plate(Caution: Do not directly touch copper plate, It will be very hot from the iron)e.Etch the Platef.Cleaning, Disposal, and the Final Touches for the Circuit Board
What has the author Earl Jacob Waters written?
Earl Jacob Waters has written: 'Electronic circuit design' -- subject(s): Electronic circuit design
Can you patent a circuit design?
Yes, since such circuit is entirely of your own and technically innovative.
How do you design a gray code circuit for the range of integers 0-15?
assalam o alikum,i am hameed ullah and a student of electronic engineering. my question is that ,,,,,,,,,,, "why we converted a binary number into gray code" and what is the difference in odd parity and even parity
Where can one learn about electronic circuit design?
Someone can learn about electronic circuit design by studying electrical or telecom engineering while at University. If someone is more interested in electronic circuit design as a hobby, then there are many web forums such as Penguin Tutor, which feature tutorials on this subject.
