answersLogoWhite

0

Use a masonry drill. If you are drilling a large or deep hole, you can use a hammer drill with a special bit. If the hole is very large, you can rent or hire someone to do concrete sawing.

User Avatar

Wiki User

15y ago

What else can I help you with?

Related Questions

How can I effectively drill a screw into concrete?

To effectively drill a screw into concrete, you will need to use a hammer drill with a masonry bit. First, mark the spot where you want to drill the screw. Then, drill a pilot hole using the hammer drill. Next, insert a concrete screw into the hole and use a screwdriver or drill to tighten it securely into the concrete. Make sure to use the appropriate size and type of screw for the job to ensure a strong and secure hold.


How do you install concrete screws?

To install concrete screws, first drill a hole into the concrete using a hammer drill and masonry bit. Then, insert the screw into the hole and tighten it using a screwdriver or drill. Make sure to use the correct size and type of screw for the job to ensure a secure installation.


How to drill a hole in concrete effectively?

To drill a hole in concrete effectively, use a hammer drill with a masonry bit. Mark the spot where you want to drill, then start drilling at a slow speed. Apply steady pressure and periodically clear out the dust. Use a vacuum to clean up the area afterwards.


How to use a Tapcon for securing objects to concrete surfaces?

To use a Tapcon for securing objects to concrete surfaces, first drill a hole in the concrete using a hammer drill and masonry bit. Insert the Tapcon screw into the hole and tighten it with a screwdriver or drill. Make sure to follow the manufacturer's instructions for proper installation.


How to use Tapcon screws for concrete anchoring?

To use Tapcon screws for concrete anchoring, first drill a hole in the concrete using a hammer drill and a masonry bit. Then, insert the Tapcon screw into the hole and tighten it using a screwdriver or drill. Make sure to follow the manufacturer's instructions for the specific size and type of Tapcon screw you are using.


What is the recommended installation method for a machine screw anchor in concrete?

The recommended installation method for a machine screw anchor in concrete is to drill a hole in the concrete, insert the anchor, and then tighten the screw into the anchor using a wrench or drill.


How do you Nail a 2 x 4 into a concrete floor?

that is a hard one. You will probly need a hole in the concrete with a drill or something. Or dynimite.


Which drill bit would you use to cut a 40 mm hole in concrete block?

A 40mm masonite drill bit could work using the right drill. But consider using a coring machine instead because its concrete.


How do you use Tapcon screws in concrete effectively?

To use Tapcon screws in concrete effectively, first drill a hole in the concrete using a hammer drill and the correct size masonry bit. Insert the Tapcon screw into the hole and tighten it with a screwdriver or drill until it is secure. Make sure to follow the manufacturer's instructions for the specific Tapcon screw being used.


How to make a hole in concrete?

Depends on the size hole you need to make and what you need to do with it. If you need to make a large hole in concrete, or totally destroy the concrete, use a jack hammer or even a sledge hammer. Or you could use a drill to drill a small hole in concrete if you need to install a fastener of some type. You can rent special drills with diamond heads at most hardware stores if you just need it for a short period of time.


What is the best way to drill through concrete using a masonry drill bit?

The best way to drill through concrete using a masonry drill bit is to start by marking the drilling spot, then using a hammer drill on the hammer setting to slowly and steadily drill into the concrete. Make sure to use a slow and consistent pressure, and periodically stop to clear out any dust or debris from the hole.


How can I effectively put a screw in concrete?

To effectively put a screw in concrete, you will need to use a hammer drill to create a pilot hole in the concrete. Then, use a masonry screw and a screwdriver or drill to securely fasten the screw into the hole. Make sure to use the correct size and type of screw for the job to ensure a strong and secure connection.