0
ifconfig eth0 up
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How would a technician permanently change the IP address of an Ethernet card on a Red Hat Linux PC?
Command to change the IP address on Linux is ifconfig.Run ifconfig to find the interface name for the connected Ethernet card. If there is only on ethernet card present on your system then the interface name would be eth0. If there are more than one Ethernet cards present on your machine then they interface names will be ethn.Once you have figurred out the interface name then ifconfig command can be used to modify the IP address$ ifconfig eth0 upeg$ ifconfig eth0 192.168.1.100 upWould assign new IP address to eth0
How do you set IP Address of a LAN card in Linux?
Assuming you're not using DHCP (in which case it would be set automatically), you would use:ifconfig eth0 10.10.0.1substituting the correct interface card and IP address, of course.
How do you release and renew your ip address in Linux computer?
Below are two different methods of how this can be done at the command line. ifconfig eth0 downRunning the above command would take the eth0 interface (the first network card) down. Which is the same as releasing the IP address from that network card.ifconfig eth0 upAfter the interface is taken down, typing in the above command would bring that interface back up.ordhclient eth0Renews the IP address assigned to it by DHCP.
Are network interfaces named sequentially in Linux?
Yes. The first configured interface is eth0, the second eth1, the third eth2, and so on.
In Linux what does 'iwconfig eth0 key 5c00951b22' do?
It sets the WEP key that will be used by that interface. Answer: Network + Guide to Networking Fifth Edition, Chapter 8. On your Linux workstation, you open a terminal window and type at the command prompt iwconfig eth0 key 5c00951b22. What have you done? C. Established the credentials the wireless interface will use to communicate securely with the access point.
How do you change your IP address in Linux?
If your router assigns IP addresses via DHCP, it is better to configure the router to pre-assign IP addresses to certain hostnames.If you do not have a DHCP server running in your router, you can specify an IP address for a network interface with the ifconfig command. For example:ifconfig eth0 192.168.20.10
How do you install a LAN card in Linux?
For modern (pretty much anything that doesn't use an ISA slot) LAN cards, there is probably no need to do anything from the Linux side. Most LAN cards are already supported in the Linux kernel, and modern distros typically use udev to automatically assign a name (such as eth0, eth1, etc...). Assuming your system does not do this, for whatever reason, here is a relatively simple method for setting up a new network card:1. Look at the dmesg on startup to see what module your network card uses (such as rt8139).2. Try activating the interface manually, by issuing the command "ifconfig " If you have no other NICs on your computer, it is probably called "eth0"; otherwise, increment the number accordingly. If the command doesn't return anything, it probably worked, otherwise the card is not at that number or is not working.3. Modify /etc/modules and add the following:alias 4. Modify /etc/network/interfaces and add the following:auto iface inet dhcp5. Restart your network, either by rebooting, or running '/etc/init.d/networking restart'
What should you do if eth0 is not present in Red Hat Linux?
If the hardware is present, but operating system can not use it, then mostly the problem is a lack of drivers for that specific hardware. Upgrading kernel or downloading and compiling drivers, if released, would help that.
On your Linux workstation you open a terminal window and type at the command prompt iwconfig eth0 key 5c00951b22 what have you done?
Network+ Guide to Networks answer: Established the credentials the wireless interface will use to communicate securely with the access point.
You want to determine whether your Linux laptop has connected and obtained a valid IP address what commands will allow you to find the information you need?
just "ifconfig" will list all of your active interfaces. look for the "inet" parameter, that will tell you the ip address. as for telling which interface is which, "eth" interfaces are ethernet they're numbered like eth0, eth1, eth2 etc. and wifi interfaces are named "wlan", and a numbered like wlan0, wlan1, wlan2 etc.
How do you set the IP address in Linux?
set the IP address with the ifconfig command use the syntax: ifconfig interface address netmask up view your network interfaces with the command ifconfig then for example to set address to 172.12.0.1 on the interface eth0 use: ifconfig eth0 172.12.0.1 netmask 255.255.0.0 up make sure you have root permissions to do this, either be logged in as root or preceed the command with "sudo". you don't have to specify the subnet mask if you don't want to, but it is generally recommended to do so.
How do you find your IP address in Linux?
Via the command line, type: /sbin/ifconfig By default, it will show every network device. Since many Linux systems use eth0 as the default network device, you can optionally type the following to view just that one: /sbin/ifconfig eth0 Under each network device will be 'inet addr' or 'inet6 addr' depending on how you've configured your system. Next to it is the IP address. If you're connected via LAN or router you may want to find your external (public IP). It could be done simply from command-line as: curl smart-ip.net/myip
