Oldsmobile Achieva

How do you get the security light on a 1997 Oldsmobile Achieva reset?

123

Top Answer
User Avatar
Wiki User
Answered
2013-06-09 13:42:24
2013-06-09 13:42:24

do not start vehicle but turn key to on position then off three times and on that third time leave it on the "on" position takes 10 to 15 minutes to reset the security light should stop blinking.

001
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


When your security light comes on and your car will not start, turn you key to the on position and wait 10 minutes. The light will go off and you need to turn the key to the off position, then restart your car.


Have the problem repaired and they will reset the light. If you DIY then disconnect the negative battery cable for 5 minutes. If that does not reset the light you will have to have it reset with an OBD2 scan tool.


To reset the security light on an Oldsmobile vehicle, first the driver must turn the key to the "on" position, without starting the engine. Next, he or she should turn the key to attempt to start the engine, but not completely, so that it doesn't start before moving the key back to the "on" position. After about 12 minutes, the light will?æbe reset, and the key should be removed.?æ


To reset the fashing dash blue security light............disconnect the hot lead on the battery and after about 3 minutes, reconnect it. Light should be off now.


Well that depends on what type of security light bulb it is. Is it for your car, backyard or porch? There are so many out today.


Oldsmobile vehicles do not have inertia/reset switches.


A 1991 Oldsmobile does not have a reset button.


The security light on a 2001 Chevy Astro Van can be reset by disconnecting the battery for 30 seconds. This resets the system and turns out the light until another problem is detected.


Just press the reset button at the fuse panel on the driver side. Press it for some seconds and it will clear the light.



2 ways, autozone can reset the light,no charge. But they can also tell you what the code # is and what you might need to repair it. Or you can disconnect the battery for approx. 5 Minutes, that should reset the cars computer.


If the coolant system (radiator and reservoir) is full and the light remains on, the probe on the coolant level sensor is probably dirty. Remove it from the radiator, clean it gently with brake clean and an old toothbrush, re-install it, refill coolant system and you should be good to go.


Push the odometer trip reset till you get to "oil" then press and hold down till it reads "100"



Open up the drivers side door and you will see a cover pannel on the dash side. Pull the open and press the reset light until the light flashes. You must have the car ON.


You need an auto locksmith-look for one that's mobile on Craigs under services.


You can disconnect the negative battery cable, wait a couple minutes then reconnect the cable. This will clear the codes and reset the check engine light but, if the reason the light came on isn't fixed the light will come back on soon.


You can do it with a scanner. Usually when the security light is flashing it means there is a problem with the passlock system. Dealer item and about $500.00-$700.00 to replace parts & reprogram.


To reset the computer on a 1992 Oldsmobile Cutlass Supreme, unhook the battery for about five minutes. Then reconnect the battery. If this does not work, look for the reset button on the computer and manually reset it.


You need an auto locksmith-it takes a specail interface with the cpu (car's comp) the dealer can do it but it is expensive. Look on craigs, select auto locksmith, services, find one that does security (chipped keys) and is mobile, make it clear pats is activated. For around 100.00 they can reset it in 5 minutes. The car won't go anywhere until it is.



on the drivers side there is a fuse panel on the dash. there you need to press the reset button once and then your change oil light will blink. then you want to press it again and the low tire pressure light will blink hold the reset button until it beeps and then let go and then press the reset button again and the light should disappear. Hope this helps!


Disconnect the neg battery cable for about 30 seconds; this will reset the computer. If there is a existing problem the code will reset however. Get yourself a HAYNES manual to identify the code and problem.


how to reset the radio security on a toyota 37409


The factory alarm causing the issue would be the security light flashing above the RPM guage. If the security light is flashing and the car will not start, follow the directions listed below. To reset the factory alarm, turn the ignition switch to the "on" position NOT the start position for 15min. You will see the security light go off after 15min.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.