0
Most home speakers are rated at 8 ohms, but your receiver should be able to work speakers as low as four ohms, with reduced output. Car stereos are normally 4 ohms, but should work up to eight ohms, with reduced output. It's all in the design of the electronics.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you connect sinotec DVD player to LG television?
Very very easy. does your DVD Player ( Home theatre ) have a HDMI cable? If it does, you can just buy an HDMi cable and connect it to Hdmi 1 on your tv and the other end to the Dvd Player and the sound a video will be very crisp. Alternatively, you can use an AV cable ( cable with yellow plugs on the end) and connect it to an AV output on your tv and DVD player. If you are using only the tv's sound this will work, but if you are using a amp,etc. you can connect 2 RCA cables to the tv and the amp for the sound.
Will you get 5.1 audio if you connect a sony DVD player to a 46 inch plasma tv with an HDMI cable and or coaxial cable?
No, you will need a surround sound receiver or amplifier with 5 speakers and a subwoofer to hear surround sound.
How do i connect a PS3 to a Phillips DVD surround system?
hook up your ps3 to your television (with HDMI cable) and depending on what kind of television you have, you need to send the audio out to the sound system. I used an optical cable for the best quality sound. Now, no matter what is hooked up to your television, it will go through your sound system.
How do you connect a Yamaha hrt 6130 surround sound to DVD tv?
Connect the digital audio output of the DVD to the the HRT-6130. The HDMI inputs on the HRT6130 are only pass-through, so audio needs to be connected on another cable. If you have a HDMI output on the DVD player, use a HDMI cable to connect it to the TV.
You have cable box DVD wsurround sound all connected to tv you want to add the vcr to this and be able to tape from cable what is the best way to connect the vcr in with the rest should you run coax?
You unhook the connection from the cable box to the TV and connect it to the VCR input. You purchase a short cable and install it from the VCR output to where the cable was connected to the TV. The TV will get the cable box signal through the VCR with no problem when you are not using the VCR. If the cable box was connected to the surround sound or Home Theater and then the TV then connect the cable box to the VCR and then the surround sound or home theater.
I am getting no sound from my DVD player which is connected to my tv and broadband?
Check the audio cable to make sure it is connected correctly and securely. It also might be that the TV does not have a sound bar so a surround sound system needs to be purchased though that is doubtful.
Can you use a fiber optic cable from DVD player to tv?
I sold this stuff for 12 years and never plugged a fibre optic cable into a TV. This should be plugged into your amplifier for your surround sound. (typically) You will not be able to tell the difference between that or a simple audio cable through a TV.
If you have direct tv and a cable box a DVD a vcr with surround sound and you would like each one to be able to go through the surround sound how should you hook them all up?
I don't understand why you would have Direct TV (sattelite) and cable TV? However, it depends on the input/output combinations of each component. I have my coaxial cable from my sattelite to the sattelite in jack on the sattelite receiver, the out to TV coaxial from the sattelite receiver run to my VCR plugged to antenna in on the VCR and a coaxial cable from the VCR to the TV coaxial antenna in on the TV. That way, you can watch sattelite without turning the VCR on, but the sattelite receiver has to be off to watch VCR or VHS tapes. Then, run video patch cords (red, white and yellow) out of the DVD to the TV (if the TV has those types of inputs on the back) If you want all three components (sattelite, VCR and DVD) to run through surround sound and NOT the TV, run only the yellow video cord from the DVD to the TV. Run the red and white to the surround sound receiver for each component. Your surround receiver should have multiple inputs for sattelite/cable, VCR and DVD.
Why do I only have sound and not the picture when the DVD player is hooked up to the TV?
Try changing the source on the television to AV1 if you only have sound but no picture from a DVD player. If it is on TV it will not play a DVD.
TV Stereo DVD VCR. Antenna cable to vcr. Vcr cable to tv. RCA cables between vcr tv. RCA cables between DVD tv. RCA cables between tv stereo. TV only works with tv remote not through DVD. Help?
put tv arial on DVD. Use DVD remote to change source on DVD from avi1 to tv channel then use DVD remote for tv.
You have Panasonic plasma tv connected via HDMI to Panasonic DVD player and sony 7.2 muteki connected via fiber optic cable why have you got no sound?
EASY: Because the TV is broken.
How do you hook up a Philips DVD player to Toshiba tv?
by cable
