0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
GFI electrical outlet at the garage where the freezer hook up keeps on tripping but when plug at the electrical outlet of the garage door openner does not trip. What is mostly the problem?
Electric motors and GFI's do not get along. the initial draw to get the compressor going is usually enough to trip the GFI. Turn the breaker off and switch the GFI for a regular outlet and you will solve your problem.
Why do CFL's keep blowing in my lamp that is pluged into a GFI outlet?
Are you sure it is the bulb that its blowing and not the Gfi tripping? Try resetting the gfi. Also try swithing to an incandescent bulb and test your gfi. Also test the cfl in a non-gfi outlet. Cfls return power they don't use and may make the gfi trip. I am not an electrician, just personal experience.
What is the depth requirement for an under ground electric house wire?
It depends on the voltage and if it is a branch ciriut or a service. If it is under 30 v olts 6 inches will work. If it is 120 volt branch circiut it needs to be on a GFI, on a 20a breaker and either in a condiut or uf cable to be 12 in . If it is not on a gfi , and it is over 20 a then it must be 18 in. Regardless the wire must be in condiut or be of UF cable to make it water tight.
Gfi receptacle first in a line of seven other receptacles in new construction that works fine without the load of the other receptacles but does not work when you add the additional receptacles?
There must be leakage current in the down stream receptacles It is going to be a trial and error method of finding the leak. Remove the GFI and make a through connection to the downstream receptacles Now go to first receptacle and install the GFI. If it holds the fault is further down stream. Keep going down the line until you find the fault. When the GFI trips and won't reset it will be the up stream feeder. Check the feeder wire for cuts or scrapes in the insulation. Replace this feeder.
Do you need a gfi plug for a spa if it is being plugged into a gfi circuit?
If your spa is connected with a GFCI circuit breaker you will not need the GFCI receptacle.
Can one use 1 circuit of a 3 wire plus ground 2 circuit cable as a GFI circuit with the other as a lighting circuit?
A GFCI can not be used on a three wire branch circuit. It has to be on a single two wire circuit.
Gfi doesn't pop but touching on outside of trailer you get a shock?
Verify that the correct connections to the GFI are correct. It sounds like the ground wire is not connected.
GFI electrical outlet at the garage where the freezer hook up keeps on tripping but when plug at the electrical outlet of the garage door openner does not trip. What is mostly the problem?
Electric motors and GFI's do not get along. the initial draw to get the compressor going is usually enough to trip the GFI. Turn the breaker off and switch the GFI for a regular outlet and you will solve your problem.
Does a food waste disposal wire have to be in conduit?
Not in residential use. Most use a cord plugged in to a GFI outlet.
What is the device designed to detect a difference in current between circuit wire called the inward and outward paths?
GFI
What is the population of GFI Group?
The population of GFI Group is 2,010.
Can GFI's be used to repair short circuits?
No. That is not the purpose of a GFI.
When was GFI Software created?
GFI Software was created in 1992.
When was GFI Group created?
GFI Group was created in 1987.
When was GFI Russia created?
GFI Russia was created in 1996.
Can you add an outlet onto the gfi next to the circuit breaker panel?
If t hat GFI is the only plug on the circuit then yes. If there are other plugs you have to find out how many so that you don't exceed the capacity of that circuit. If the GFI is the only plug there, turn the power off to it at it's breaker and run the appropriate wire to the new plug you want to install. Wire in the new plug, then make the connections at the old GFI plug. Always work towards the power, even if the circuit is dead. It's good practice. This way you rarely if ever have to work on live circuits. Start at the furthest point in the circuit away from the electrical panel and work toward it. You can have the new outlet protected by the GFI if you connect the wires from the new outlet to the LOAD side of the GFI. If the GFI is still new there is usually a yellow sticker covering the screws, those 2 screws are the LOAD side meaning that if anything happens downstream on that circuit to make a GFI trip the GFI will sense it and turn the circuit off. If you want just a standard outlet then put the new wires on the same screws as the old wires on the GFI. Once you're done, and all the boxes are closed and safe, turn the breaker back on.
Can you back wire an outlet on a gfi circuit?
Don't know what you mean by back wire, but most GFCI outlets have a circuit to attach additional outlets that will be protected by the GFCI. Keep total load in minds.
