If you have good access to the wiring this is relatively easy to do. Each of the 10 lights is connected to another in parallel in a "daisy chain" fashion. Light 1 is connected to the switch, light 2 is connected to light 1, light 3 is connected to light 2 and so forth.
Let's say it is light 5 that you wish to switch separately. You can first install the new switch by either adding a new box or modifying old switch box. There are two gang switches that will fit the form factor of a single switch.
TURN OFF THE POWER TO SWITCH BOX. Using the same supply input at original switch, add a new black wire to the wire nut for input to original switch and connect this to the input of new switch. Then run a new wire to light 5 and connect black wire to the output of new switch. Connect all the white wires together in switch box and separately connect all bare wires together in switch box.
Now at light 5 undo the black and white wire coming from the fixture, and reconnect the wire nuts so that there is a direct connection between light 4 and light 6. Do the same for the ground if present (bare wire). You now have the fixture wires hanging free. Now connect the black wire from new switch to the fixture black wire and white to white and you are done.
In any situation you want the switch located so you can have light before entering the space. With basements you might use what is called a 3-way switch with one at top and one at bottom of stairs. Think about how you are going to use the space. You wouldn't want to put a single switch at the top of the stairs and then have a TV room downstairs and have to go up the stairs to turn off the lights and then go back downstairs to watch TV. The more control you have over the lighting you use, the better you can tailor lighting to the activity being performed.
The circuit will not work. In a three way lighting circuit system the middle switch needs to cross the traveller wires to be effective. A double pole switch in the circuit will just open both traveller wires and disrupt the current flow in both wires. No current flow, no lights.
Without knowing some more facts, there could be several different answers to explain why a ceiling fan's lights "go out":someone has turned them off at the switch for the lights on the fan unit;the light bulbs are "dead" and need replacing because their filaments have broken;there is a fuse protecting the lighting circuit and it needs replacing because it blew from the surge of high current that sometimes happens when a light bulb "dies";there is a timer in the fan unit which turns the lights off after a certain period of time;the wiring from the switch to the light has become disconnected;the switch in the fan that controls the lights is broken and needs to be replaced...
A clap switch is an electronic device that can be turned off and on by clapping the hands. This type of switch is commonly used in lighting.
To control a light with a switch, the switch has to be connected in series with the light fixture.
You can use incandescent, fluorescent or halogen lighting fixtures meant for indoor use inside a home. For example, you can purchase incandescent wall lights that are connected to a dimmer switch with incandescent lamping. Fluorescent lights might be in models of ceiling lights, chandeliers and pendant lights. Fluorescent lights are energy efficient lighting choices. Halogen lamps are used in some recessed lighting for indoor use. Floor lamps may also use halogen bulbs. Read carefully to see what type of indoor lighting can withstand damp settings such as the bathroom.
it connected to a break lights switch, attached to a break pedal
no it will not, because they're not connected with the same switch
A SPST switch is the type used for turning the lights on and off in your home lighting systems. It is just basically just an on - off switch.
No
There are several options for outdoor lighting. One can choose lights that are wired into the house with a switch. They can be wall sconces or overhead lights. One can choose a wide variety solar lights available. They use the sunlight to charge special batteries. They have light sensors that turn the lights on at dusk.
On your dash just to the right of your headlight switch is a dimmer wheel switch that controls the lighting brightness of your guage lighting . Check to see if it has been rotated all the way down
if the switch is lighting up, then the fuse is fine. check the bulbs.
Just to the right of the headlight switch on your dash is a dimmer wheel switch for your gauge lighting , if the switch is rotated all the way down ( past the detent ) the interior lights won't come on . Also , if the switch is rotated all the way up ( past the detent ) the interior lights will come on with the doors closed
The 1996 GMC Yukon brake lights work by receiving power from the brake light relay switch. The brake light relay switch is connected to the brake pedal.
If your courtesy lights are staying on with the doors closed and there is no door ajar warning light , check on your dash to the right of your headlight switch. There is a dimmer wheel switch for your guage lighting , if it has been rotated all the way up that turns on your courtesy lights when the doors are closed
switching on the tourch for example is when as you switch it on it will move the switch connecting it to a circuit that lights up the bulb and when you switch the switch off the switch will move breaking the circuit