answersLogoWhite

0


Best Answer

How do you install an alternator belt on a 1986 GMC s15 pickup truck

User Avatar

Wiki User

โˆ™ 2008-10-19 04:46:28
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you install an alternator belt on 1986 GMC s15 pickup truck?
Write your answer...
Submit
Related questions

Where do the alternator wires go on a 1986 Nissan pickup?

need diagram for 1986 Nissan truck alternator


How do you replace the alternator on a 1986 Nissan truck?

There are two bolts on the bottom of the alternator that you can't see but you can feel them, these are the pivot bolts, remove them. Then remove the adjustment bolt on top of the alternator. Remove wiring from back of alternator. Reverse instructions for install.


Where is the voltage regulator on my 1986 GM pickup?

Inside the alternator


The charge and brake lights on 1986 Toyota pickup stay on?

Replace Alternator


Where is the ignition coil on a 1986 Chevy silverado pickup truck?

no


Need a wiring diagram for 1986 Nissan truck alternator?

I unhooked wires on alternator but did not mark wires


What is the wheel size on a 1986 Mazda b2000 pickup truck?

The 1986 Mazda B2000 pickup truck has 14"x5.5" rims. The OE tire size is 205/75R14, and 195R14 tires also fit ideally.


Can you put a 1986 Chevy pickup truck transmission to a 1994 gmc pickup truck?

There are so many variables at work here that i don't think anyone could tell you.


What is the firing order of a 1986 Nissan pickup truck with 4 cylinder?

1324


How much does a 1986 Chevrolet 3500 Pickup Truck weigh?

Look on the inside of the door there is a small sticker that will have the truck weight!


How doi remove ignition without key from 1986 Toyota pickup truck?

Begin by removing the retaining ring at the top of your 1986 Toyota pickup truck ignition switch. The ignition switch will slide out. Remove the wiring harness from the back of the ignition switch.


What is the horsepower of a 1986 Chevy pickup with a 305 motor?

the 1986 Chevy truck 305 HO produced 180 hp


What is the towing capacity of a 1986 FWD Toyota pickup truck?

3500lbs manual, 2000lbs auto.


Where is the alternator on a 1986 Nissan truck?

look by passenger front tire toward motor and u will see.


What is the fair market price of a 1986 Nissan pickup truck?

A 1986 Nissan Deluxe 4+4 pickup low retail value, $1725. Average retail, $2750. High retail, $4350. It's all about condition.


Where is the fuel filter on a 1986 Chevy c10 truck?

The 1986 Chevrolet C10 pickup truck fuel filter is located inside of the fuel tank. The fuel tank will need to be removed in order to change the fuel filter.


Has Kurt cobain ever been to jail?

Yes, in 1986 Kurt Cobain was arrested for vandalizing a pickup truck


How do you install lock cylinder in 1986 Chevy truck?

Ignition Lock? or Door Lock?


What could be some reasons why a 1986 Ford Ranger truck will not start?

Loose cables, bad battery, alternator or starter.


Why would a 1986 smaller size pickup truck have 2 brake fluid reservoirs?

Does it have a manual transmission with a hydraulic clutch ?


What is the horsepower rating for a 1986 chevroler C-10 truck with a 4.3 liter ebgine?

The 1986 Chevrolet C 10 pickup truck with a 4.3 liter engine had a horsepower rating of 143. The horsepower rating was slightly higher or lower depending on the transmission application.


How do you use the four wheel drive on a 1986 Nissan pickup?

stop truck put in 4hi or4lo then go stop truck put in2wd and back up about 3 feet you will hear aclick


Is a 1986 Chevy truck the same body style as a 1994 Chevy truck?

No. 1986 was the third generation C/K series, which ran from 1973 to 1987. A 1994 pickup is a fourth generation model on the GMT400 platform... the fourth gen pickups were 1988 to 1998.


What are the spark plug gap settings for a 1986 Nissan Pickup truck?

service manual says .31 to.35 for ngk plugs.


How do I Change an alternator on a 1988 Toyota pickup truck?

On a **1986** Toyota Pickup (Hopefully they are similar): Unhook the positive end of your battery from the rest of your truck's electrical with a wrench. Next, there is a plug on the back of the alternator, push in the clip on the side and unplug. Next to the plug us a rubber housing, pull this back and take the screw off, removing the wire cable it was holding. There are now only two bolts holding the alternator. The first one is up top and connects to a rail that guides the alternator left and right (to tighten the alternator belt) unscrew this. Next, remove the trucks skid plate up front, there should be 4 bolts holding it in place. Once this is done, take out the coolant hose (a 1' hose with a slight S-Bend in it, it may take some wiggling to get it off). Next remove the lower bolt from underneath the alternator and pull the alternator out from the bottom. Once you replace the alternator you need to tighten the belt, it needs to be about 80 +/- 20 lbf You may have to take your truck into a local shop to have them tighten the belt for you ($30 labor) if you don't have the right torque equipment. It is a good habit to always disconnect the negative battery post first when you start the job and reconnect the negative battery post last when done with the job.