0
it is easy just find the belt tensioner and put a socket wrench on it and push it down and the belt will be loose just pull of the belt off and then put the new belt on the pulleys the correct eat there should be a diagram on the top of the radiator if it is not there then you need to remember what the belt you took off looked like take picture with your camera phone. If you do not know what a belt tensioner is go to autozone.comand look at the picture then find itbon your engine that's it Good Luck. The belt goes through the front left side motor mount. The mount has to be moved to be able to install belt
What else can I help you with?
How do you replace the water pump on a 1997 Oldsmobile regency?
To replace the water pump on a 1997 Oldsmobile Regency, first, disconnect the battery and drain the coolant. Remove the serpentine belt, then unbolt and take off the water pump, ensuring to clean the mounting surface of any old gasket material. Install the new water pump with a new gasket, torque the bolts to the specified settings, and reassemble the serpentine belt and any other components removed. Finally, refill the cooling system with coolant and reconnect the battery.
How do you replace water pump on 1997 Oldsmobile regency?
To replace the water pump on a 1997 Oldsmobile Regency, first, disconnect the negative battery terminal and drain the coolant. Remove any components obstructing access to the water pump, such as the serpentine belt and any hoses. Unbolt the water pump from the engine block, clean the mounting surface, and install a new gasket on the new pump before securing it in place. Finally, reassemble everything, refill the coolant, and reconnect the battery.
How do you install a water pump in a 1997 Oldsmobile aurora?
remove and replace water pump in 1997 Oldsmobile aurora
How do you replace an idler pulley on a 1997 Ford F150 5.4ltr?
Remove serpentine belt. Remove pulley. Install new pulley. Install serpentine belt.
What is the serpentine belt diagram for a 1997 Oldsmobile 88?
I could send a photo - email me at ken.elder@shaw.ca
What is Code p0171 1997 on Oldsmobile regency?
Trouble code P0171 means: Fuel Trim System Lean (Bank 1
How do you change idlers pulley on a 1997 Oldsmobile Aurora?
To change the idler pulley on a 1997 Oldsmobile Aurora, first, disconnect the negative battery cable to ensure safety. Then, remove the serpentine belt by using a wrench to relieve tension on the tensioner pulley. Next, unbolt the old idler pulley from its bracket, replace it with the new pulley, and secure it in place. Finally, re-install the serpentine belt, ensuring it's properly aligned, and reconnect the battery.
How do you replace the idler pulley on 1997 Northstar V8 in Oldsmobile aurora?
To replace the idler pulley on a 1997 Oldsmobile Aurora with a Northstar V8 engine, first, disconnect the negative battery cable. Remove the serpentine belt by using a wrench on the tensioner pulley to relieve tension. Then, unbolt the old idler pulley from its mounting bracket and replace it with the new pulley, ensuring it’s securely fastened. Finally, re-install the serpentine belt and reconnect the battery cable.
Where is the thermostat located on a 1997 Oldsmobile regency?
On a 1997 Oldsmobile Regency, the thermostat is typically located near the engine, specifically on the engine's coolant outlet housing, which is situated at the top of the engine block. To access it, you may need to remove the upper radiator hose and the housing cover. It's advisable to refer to the vehicle's service manual for precise instructions and safety precautions when replacing the thermostat.
Where can you get a diagram of the serpentine belt for a 1997 E420 V8 Mercedes Benz?
i need a digram on how install a v belt on a 1997 e420 Mercedes
Where is the fuel filter on a 1997 Oldsmobile Regency?
On a 1997 Oldsmobile Regency, the fuel filter is located along the fuel line, typically mounted on the underside of the vehicle. It is commonly found near the driver's side, just in front of the rear axle. To access it, you may need to lift the vehicle for better visibility and reach. Always ensure to relieve fuel system pressure before attempting to replace the filter.
How do you reset the traction light in 1997 Oldsmobile regency?
To reset the traction light in a 1997 Oldsmobile Regency, first, ensure that the vehicle is on a flat surface and the traction control system is functioning correctly. Turn off the ignition, then restart the vehicle. If the light remains on, it may indicate a persistent issue that requires diagnostic testing. If necessary, consult the owner’s manual or a professional mechanic for further assistance.
