Nissan Maxima

How do you install valve cover to a 97 Nissan Maxima?

123

Top Answer
User Avatar
Wiki User
Answered
2011-09-13 04:51:13
2011-09-13 04:51:13

How to install valve cover to a 97 Nissan Maxima.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


The PVC valve on a 1999 Maxima is located in the rear valve cover just behind the throttle body.

The PVC valve on a 1999 Maxima is located in the rear valve cover just behind the throttle body.

The PCV valve is located in the rear valve cover,just behind the throttle body

The PVC valve on a 2000 Maxima is located in the rear valve cover just behind the throttle body. REMOVAL # Grasp the PVC valve and pull it out of the valve cover

It's located in the rear valve cover, just behind the throttle body.

where is the location of the modulator on Nissan maxima transmission

Where is the coolant bleeder valve located on a 2003 nissan maxima 3.5

The PCV vavle is located in the rear valve cover just behind the throttle body

see the egr valve location on the 1999 Nissan Maxima-it should be very similar.

The PCV valve is located inline in a hose between the valve cover and throttle body. Make sure to check the hose and replace if cracks are found.

Yes, there is a problem with the design of the 2002-2003 valve covers. It's best to replace them with valve cover (rocker cover) for a 2004 maxima. They are exact fit, work better and are MUCH cheaper than the 02-03 valve covers. You must order gaskets seperately and the 04 valve covers come with a new PCV as well.

I shopped around Charlotte, NC. The best price I got in a reputable shop was $400. Mine is a 1993 Maxima GXE, 3.0 litre. Quite a shock for replacing a valve cover gasket.

The PVC valve on a 2001 Maxima is located in the rear valve cover just behind the throttle body.

On a lot of these vehicles, the PVC valve is located on top of the valve cover, or a hose leading from the valve cover to the intake. You have to remove the right front wheel. It will be in the block. It is in an awkward place and Nissan charges about a 100.00 to install it. You can do it your self though.

The PCV valve is located in the top driver side of the engine, right by the intake manifold. The PCV valve is located in the rear valve cover, just behind the throttle body. There's a rubber hose connected to it. To remove it, just pull it out of the valve cover.

The idle control valve for your 1995 Nissan Maxima can be found on top of the engine. The idle control valve will be attached to the back of the injector fuel pump.

The EGR valve on a 1999 Maxima is bolted to the rear cylinder head,at the transaxle.

The EGR valve is bolted to the rear cylinder head at the transaxle end

The EGR valve is bolted to the rear cylinder head at the transaxle end

Swirl Control Valve Control Vacuum Switch

you don't, the car has an expansion valve by the evaporator.

It all depends on the production date of your Maxima. Federal emission Maxima 06-2000- 06-2001 are EGR delete.

The EGR valve is bolted to the rear cylinder head at the transaxle end

The PVC valve is located in the breather separator under the intake manifold.

The EGR valve is bolted to the rear cylinder head at the transaxle end


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.