0
How do you pull 1 of 6 lights off a 3-way switch and add a single switch for that 1 fixture?
Wiki User
∙ 13y ago
One 1,000 watt light will push a typical circuit breaker close to its limit. Six such lights will require wiring and circuit breakers to handle the load. Figure one circuit breaker per light. That means not only six switches but six switches, each on a different circuit breaker. Don't overload the wiring or it could cause a fire.
Wiki User
∙ 16y ago
Wiki User
∙ 13y agoMost likely the 6 lights are fed from one another. At each light there will be a black, white and ground coming into the fixture and another set leaving. The light is connected to these wires by wire-nuts. Remove the light in question from the black supply wire. From your new switch run a typical Romex wire to the light. Put black electric tape on the white wire at each end to indicate it is a hot wire. Connect the Romex black and white wire with tape to each terminal on switch. At the light end connect one wire to light wire you removed previously and the other to the wire-nut where the light was previously connected.
Add your answer:
Earn +20 pts
What does a 4 way switch do?
For starters, a four way switch must be connected to either a four way switch or a three way switch on either side. Said differently, here are some common combinations: 3way---------4way-----------3way 3way---------4way-----------4way------------3way 3way---------4way-----------4way------------4way----------------3way etc. If you are using a four way switch anywhere in a circuit both ends must have three way switches. You can use as few as one four way between the three ways, or as many as you would like. First of all, connect your white (neutral) wire straight through every box, from the power source to the light fixture being controlled. That neutral has nothing to do with the switches. On your three way switches you will see two bright screws and one dark. (Excluding the green grounding screw). One three way switch will have its dark screw connected to the power source. Two wires will run from the bright screws to the next box (the 4 way switch box). Those two wires will connect to the two bright screws on one side of the four way. The four way also has dark screws, but two of them. Connect two wires to these two dark screws, and run them to the next switch box. If the next switch box is another 4 way, repeat this again and again until you get to the last switch (a three way). Wire the last three way as follows: the two wires coming from the previous 4 way go to the bright screws. The hot wire feeding the light fixture will be the one to connect to the single dark terminal of the last 3 way switch. That's it! As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.If you do this work yourself, always turn off the powerat the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicatorto insure the circuit is, in fact, de-energized. IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
How is one light controlled by three switches?
That is called a 4 way light switch circuit. On each end of the circuit you install a 3way switch and in the middle you install a 4 way switch.Answer using British TerminologyIn the UK, 'three-way' switches are called 'two-way' switches (more logical, if you think about it!), and the 'four-way' switch is called an 'intermediate' switch.
Can you replace a 3-way light switch with a standard switch and cap off the wires or can you use the 3-way switch and make it into a standard switch?
It can be done but it requires knowledge about how a 3way is wired to convert it to a regular switch. It would involve testing live wires to determine where power starts at. You can't just replace one switch.
Can you connect black wire to red wire?
In some cases in residential wiring you do. From a light fixture junction box to a switch box, the cable is a two wire, black and white. To connect the switch into the circuit at the fixture box, the "hot" conductor is connected to the white wire that goes down to the switch. The switched "hot" comes back on the black wire and this is then connected to the fixtures black wire. The white (neutral) is picked up in the fixtures junction box and connected to the fixtures white wire.
How do you connect two way electrical switch?
The two way switches work in pairs. We find most of them in our houses where the light bulb can be operated by two switches each at the far end to the other. Each switch consists of three terminals two of which are connected. When one switch is open and the other is closed then the bulb glows and viceversa
How do you control a lamp from three different positions?
we use 2-3way switch and 1-4way switch
How do you wire a one light to be operated from 4 location?
you will need 2-3way switch and 2-4way switch
What does a 4 way switch do?
For starters, a four way switch must be connected to either a four way switch or a three way switch on either side. Said differently, here are some common combinations: 3way---------4way-----------3way 3way---------4way-----------4way------------3way 3way---------4way-----------4way------------4way----------------3way etc. If you are using a four way switch anywhere in a circuit both ends must have three way switches. You can use as few as one four way between the three ways, or as many as you would like. First of all, connect your white (neutral) wire straight through every box, from the power source to the light fixture being controlled. That neutral has nothing to do with the switches. On your three way switches you will see two bright screws and one dark. (Excluding the green grounding screw). One three way switch will have its dark screw connected to the power source. Two wires will run from the bright screws to the next box (the 4 way switch box). Those two wires will connect to the two bright screws on one side of the four way. The four way also has dark screws, but two of them. Connect two wires to these two dark screws, and run them to the next switch box. If the next switch box is another 4 way, repeat this again and again until you get to the last switch (a three way). Wire the last three way as follows: the two wires coming from the previous 4 way go to the bright screws. The hot wire feeding the light fixture will be the one to connect to the single dark terminal of the last 3 way switch. That's it! As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.If you do this work yourself, always turn off the powerat the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicatorto insure the circuit is, in fact, de-energized. IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
You have an outlet with three light switches controlling three different lights what is this called?
A triplex outlet. It is a simple device unless one or more of these switches are "3way" switches.
What are the release dates for 3Way - 2008?
3Way - 2008 was released on: USA: 4 February 2008 (Los Angeles, California)
What are the release dates for 3Way - 2008 LadyCops Brotherly Love?
3Way - 2008 LadyCops Brotherly Love was released on: USA: 6 July 2009
What are the release dates for 3Way - 2008 Psychodrama 1-7?
3Way - 2008 Psychodrama 1-7 was released on: USA: 7 April 2008
What are the release dates for 3Way - 2008 Siobhan Sizzles 1-8?
3Way - 2008 Siobhan Sizzles 1-8 was released on: USA: 13 April 2008
Do pioneer 3way 6x9 speakers fit in the rear doors of a 2002 accord coupe?
Do pioneer 3way 6x9 speakers fit in the rear doors of a 2002 accord coupe?
What are the release dates for 3Way - 2008 Rhonda Rapid Delivery 1-9?
3Way - 2008 Rhonda Rapid Delivery 1-9 was released on: USA: 20 April 2008
How do you insulate 3way valve for the fcu?
You insulate the 3way valve for the FCU to control temperatures. If the valve is left uninsulated, the contents will either lose or gain temperature depending out external conditions.
How is one light controlled by three switches?
That is called a 4 way light switch circuit. On each end of the circuit you install a 3way switch and in the middle you install a 4 way switch.Answer using British TerminologyIn the UK, 'three-way' switches are called 'two-way' switches (more logical, if you think about it!), and the 'four-way' switch is called an 'intermediate' switch.
