0
With great care. The standard light bulb is comprised of a continuous glass housing. The only thing that goes through the glass are the two wires that provide the current pathways to the inside of the envelope where the filament is. To create a hole in a bulb requires a lot of patience, a lot of care and the use of some sort of abrasive tool to grind the hole. Though it might be possible to create a hole by actually drilling it, it is improbable that one could do it without ending up breaking the bulb. The glass isn't that thick, and because the surface is round, smooth and hard, it would be exceedingly difficult to get the drill bit to bite (start). A very small rotary abrasive bit in a dremel tool is probably the best bet. Eye protection is a MUST and hand protection is strongly recommended. Oh, and you are being warned up front: be very careful about what you do with your light bulb with the hole in it. Aiight?
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
Which was invented first the light bulb or electricity?
electricity because a light bulb needs electricity
Does the middle bulb on the tail light work?
If there is a bulb, it should work.
The power delivered to the light bulb is 23.1 W. What are the two possible resistances of the light bulb?
A: HARD TO SAY because a bulb has different resistance as it warms up
What part of a light bulb has the most resistance?
the actual filament itself in a light bulb has the most resistance,this is why it glows and produces light,the rest of the bulb is sufficiently engineered to carry the voltage and current applied to it without producing too much heat.
Why does the brake light on the integra not light up when you turn on the light but it light up when you brake?
The Integra uses a dual-filament bulb in the tail light, which has one contact for the running light (the lights you turn on at night) and another brighter one for the brake light (only goes on when you press the brake pedal). You have replaced the bulb with the wrong type. You will need a 2057 bulb for the Integra.
What is best known for Thomas Edison?
Thomas Edison is best-known for the light bulb.
Where is the Light bulb list for 2005 cobalt?
2005 Chevrolet Cobalt Light Bulb Replacement GuideHigh & Low Beam Headlamp Light Bulb Size:9007LLParking Light Bulb Size:3157LLFront Turn Signal Light Bulb Size:3157LLRear Turn Signal Light Bulb Size:3057LLTail Light Bulb Size:3057LLStop Light Bulb Size:3057LLHigh Mount Stop Light Bulb Size:912Fog/Driving Light Bulb Size:H11-55WLicense Plate Light Bulb Size:194Back Up Light Bulb Size:921Front Sidemarker Light Bulb Size:194Rear Sidemarker Light Bulb Size:194Map Light Bulb Size:2825LLDome Light Bulb Size:562Step/Courtesy Light Bulb Size:212-2
Is a light bulb a compound?
No. The light bulb is two words, not a combination of light and bulb.
Why does a light bulb light in a closed circuit?
A bulb does not light up if there is no voltage available across the bulb, or if the bulb is burned out.
What is the name of the light bulb?
A light bulb
Why do you have a light bulb?
Light bulb provide electrical light.
What did Einstein do 100 times to get it to work?
To build the light bulb.
Is light bulb a compound word?
Yes, "light bulb" is a compound word because it is made up of two separate words, "light" and "bulb", that are combined to create a single noun.
Which came first the telephone or the electric light bulb?
The electric light bulb came first but was patented later that the telephone was.
What type of light is a light bulb that uses a filament?
An incandescent light bulb uses a filament that produces light by heating it until it glows. This type of light bulb emits a warm and yellowish light.
Can a laser be made from a light bulb?
No. Laser light is coherent. Light bulb light is not.
How many apples does it take to light a light bulb?
I think that the orange and nails light up the light bulb because the acid energy goes through the nails and into the wires connected to the light bulb and powers the light bulb
