0
I'm not sure if you'll find a specific airbag code or not. Usually, the codes refer to engine management systems.
At any rate, the codes are read via an access port located under the dash on the driver's side.
Code readers can be purchased at most any good parts store, or most of the big box stores will read them for you at no charge.
What else can I help you with?
What is the correct tire pressure for a 2002 Pontiac sunfire?
The side of the driver's door on my 2002 Pontiac sunfire is a little hard to read, but I believe it says 30 PSI.
How do you replace the tail light on a 2001 Pontiac Sunfire?
Read more: http://wiki.answers.com/How_do_you_replace_the_tail_light_in_a_2000_pontiac_sunfire#ixzz1Nur0XSlq
How do you reset the airbag light on a vw transporter?
To reset the airbag light on a VW Transporter, you typically need to use an OBD-II scanner or diagnostic tool that can read airbag codes. First, connect the scanner to the vehicle's OBD port and turn on the ignition without starting the engine. Follow the scanner's instructions to read the airbag fault codes, then clear the codes to reset the airbag light. If the light returns, there may be an underlying issue that needs addressing.
How do you turn off the air bag light on a 2002 Pontiac Sunfire?
Hey - I'm a fourth-year automotive service tech up here in Alberta... If your airbag light is on, chances are there's a fault in the wiring somewhere - or GM might just be jacking you around. Sometimes vehicles trip error codes in the computer periodically as a scam for dealers to get your car into the shop. Unfortunately, your only option is to take your car to a dealership, or any shop with a scantool that can read and erase diagnostic trouble codes on your car. Lucky for you, this service is often free, so stop in to your local automotive shop and ask them to clear the codes to turn that damn airbag light off! Hope this helped, take 'er easy.
Why does your 98 Pontiac sunfire's check engine light always come on and the car dies 2-3 times a day?
The only way to know what is wrong is to have the error codes read that are set in the computer from the check engine light. Most auto parts stores will read the code for free and give you advice on repairing the problem.
Where do you find default codes for a 1997 Pontiac transport?
Assuming you want to read the DTC's (Diagnostic Trouble Codes) stored in your 97 Pontiac, your local auto parts store can read them (if any exists) for you at no cost. You can google the results you get for a definition of codes. Keep in mind the codes that come up may only be the result of another underlying problem.
How do you check for a vacuum leak on Pontiac sunfire?
To check for a vacuum leak on a Pontiac Sunfire, start by inspecting all vacuum hoses for cracks, tears, or disconnections. You can also use a smoke test, where smoke is introduced into the intake system to visibly identify leaks. Additionally, listen for hissing sounds while the engine is running, which can indicate a leak. Finally, using a scan tool to read any related trouble codes can help pinpoint issues associated with vacuum leaks.
Will an actron scanner cp9690 read airbag problems on a 2004 jeep wrangler?
The Actron CP9690 is primarily designed for reading and clearing OBD-II trouble codes, which includes some airbag codes for vehicles equipped with OBD-II systems. However, the effectiveness of reading airbag problems can vary depending on the vehicle's specific systems and the scanner's capabilities. For a 2004 Jeep Wrangler, while the scanner may read some related diagnostic trouble codes, it may not provide comprehensive coverage for all airbag-related issues. It's advisable to consult the scanner's manual or check compatibility for specific airbag diagnostics.
How do you read oil dipstick in a 1997 pontiac sunfire?
The oil dipstick is built into the oil filler cap. Unscrew the cap, pull the dipstick out, wipe it dry and reinsert it. Remove it again to read the oil level.
How do you turn off the airbag light for a Skoda superb?
To turn off the airbag light on a Skoda Superb, you typically need to use a diagnostic scanner to read and clear the fault codes stored in the airbag system. Ensure that there are no underlying issues with the airbag system, such as disconnected sensors or faulty components. If the light remains on after clearing the codes, it is advisable to consult a qualified mechanic for further diagnosis. Always prioritize safety and do not ignore airbag warning lights.
How do I reset an SVX airbag light?
To reset an SVX airbag light, you'll typically need to use an OBD-II scanner that can read and clear airbag codes. First, connect the scanner to the vehicle's diagnostic port, turn on the ignition, and follow the scanner's prompts to read and clear any airbag fault codes. If the light persists after resetting, it may indicate an underlying issue that needs to be addressed before the light can be cleared permanently. Always consult the vehicle's service manual for specific instructions related to your model.
How do you reset SRS airbag Volvo s60?
To reset the SRS airbag light on a Volvo S60, you typically need to use an OBD-II scanner that can read and clear airbag codes. First, connect the scanner to the vehicle's OBD-II port, usually located under the dashboard. After retrieving any fault codes and addressing any underlying issues, you can clear the codes to reset the airbag light. If you don't have access to a scanner, it's best to consult a professional mechanic or a Volvo dealership for assistance.
