0
Connect your recording device to the preamp output on the back.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What do you set your amp to for 2 12 subs?
to mono if your amp will allow, also this is for single voice coil. otherwise run in mono parallel to run dual voice coils.
How do you wire a dual voice coil to an amp?
If you want to run both coils,you have to wire the positive to positive and negative to negative on your sub,then run a wire from each plug to the amp. Positive to the positive side of the amp and negative to negative side of the amp,(you can run in bridge mode or stereo if your amp can handle the load)
How do you install two amplifiers into a subwoffer?
its better to get one amp for you sub then 2 because your going to have to spend more money with wiring and stuff. But if you really wanna do it you have to wire one voice coil to the other one and same for the other amp but if you have one voice coil you have to split the wiring into 2 neg and 2 pos then wire upto amp. HIGHLY NOT RECOMMENDED
What do you need to play records on a home theater system?
First you need a Phonograph. Phonographs (record players) can be connected to a stereo or A/V surround receiver using a pair of standard red/white stereo audio cables. The important thing to understand is that many record players do not amplify the signal, which means you need a pre-amp or "phono amp" somewhere in the mix to get your sound. Check to see if your record player has a built in pre-amp. If not, your A/V receiver needs a dedicated phono input with a built in pre-amp.
What app can you record from your electric guitar with?
I use Fruity Loops Studio, with amplitube 3 as my amp software.
How do you wire amp to 1 ohm load?
need more info but I'll give it a shot and hope i answer your question. You will need one of the following to get your desired ohm load: 1- single voice coil at 1 ohms 2 - single voice coil at 2 ohms wired + to +, - to - 2 - dual voice coil at 4 ohm all wired + to +, - to - so that you only have 2 wires conected to the amp. hope this helps.
If two four ohm single voice coil subs are wired in parallel how many ohms will be on the amp?
Two four ohm speakers in parallel is two ohms. Make sure the amp is rated for that load impedance, or you could damage it.
Why does audacity make a muffled sound when you record your guitar which is in my?
My electirc guitar sound really muffled on Audacity as well miking the amp.
How do you install an Alpine sub-woofer?
Make sure that all voice coil jumpers are connected propertly and then run your wires to the amp and your all set.
How many channels do you need to power my subwoofer?
mono or two channel are the best for subs but it depends on if your sub is dual voice coil or single voice coil, what ohm load the amp can handle, and if it is single voice coil and are using one sub you need to make sure you can bridge a 2-channel amp if that's the kind you chose... Next question you ask it may help to add a bit more detail. If I knew the sub brand and model, ohms, and if it's dual or single voice coil i could help answer that much better.
How do you connect your radio to your car alarm siren?
you can but, you need to open the siren of your alarm system and disconnect the chip inside. then reconnect that to a voice amp or your stereo, simple as that.
Ahuja speaker price list in chennai?
Amp SSA 250 1 No. Rs. 9,500.00Spekar SR 250 2 Nos. Rs.12,000.00Mic ER 11 EM 11 1 No. Rs. 4,500.00AM X 60 1 No. Rs. 2,750.00Mic Stand 1 No. Rs. 800.00Horn 2 Nos. Rs. 2,500.00
