Repeatedly shoot rainbows at it using your dog as the shooter
If you are trying to replace you radio you would have to remove the bezel. Take the two knobs off, then gently pull off the bezel till it can't move (should be about a couple of inches then it gets stuck), follow the rod down towards the right side off the gas peddle and remove the two screws holding it. Now you can pull the bezel out further to disconnect the cables. Don't diconnect the rod from the back of the controls just unscrew it. if equipped with tilt steering tilt the column all the way down remove the steering column covers remove the screws at the top and bolttom of the instrument cluster bezel and detach it from the vehicle
Caution: The air control bezel uses a thin plastic overlay fixed onto an open frame. The radio bezel has locking ribs on the bottom- when removing the radio bezel, the ribs can puncture the air control bezel. Place a piece of heavy tape or carboard over the air control bezel to protect it. Use a thin plastic tool to pry the bottom of the radio bezel until it comes loose. Then work around the sides until the bezel separates from the dashboard. Unplug the connectors at the top. It will be attached by the AC harness- remove the connector (which can be a bit tough) or just flip the bezel over the steering wheel. Remove the three 10 mm bolts that hold the radio. Remove the radio and unplug the connectors from the back. GM radios are a double DIN style, so most replacements will need an install kit that will add a blank plate or storage pocket.
what is the value of an 1886 The Franklin Mint Watch
Vestal Observer Watch, remove back replace battery related issues. Get free help, solutions & advice from top Vestal experts.
1994 Metro; The bulb is located on the back of black bezel surrounding the radio & heater controls, In the center between the slideing levers. You have to remove the bezel,there are 3 retaining screws,1screw in the center below the 2 moveable a/c vents & 2 screws below the bar under the slideing levers. the bottom of bezel will release, But the top of bezel has two metal retaining clips right above the moveable vents that you have to be very careful when removeing. The bulb mounting base just twists out there is a plastic retainer for the wires. When replaceing bezel put the top of bezel around vents & make sure you can move them.dont push in the bezel yet. Put the slideing levers in the center position make sure they are exposed & moveable then push the top of the bezel in the clips & secure with the screws. This black BEZEL is easy to break & you would have to hunt for one in the salvage yards to replace it so be careful.
The best way to do it is to remove the whole center bezel (where the radio sits in) be very careful not to crack it. there are screws holding it in, you'll see them. If you have a radio installed, do what you have to do to get the bezel out. The vents on the top of the bezel are attached to it, so be carefull and work it out "SLOWLY". then remove the carpet panels, which are running from front to back on the side of the seats. there are 3 screws holding each one in. then remove the console bezel where the two window switches set into. you'll see the hex head nuts, two on each side (i believe) of the console bezel and two underneath where the radio bezel sat on. this should be enough to raise the console up and look underneeth the switches and you'll find them held in by two more hex head screws. reverse the installation. good luck!
If you're asking how to remove the back cover panel:1. Looking at the back of the monitor, you'll see two screws near each bottom corner. Remove those.2. Inserting a thin tipped standard slotted screwdriver, pry between the back cover and front cover (bezel) gently.3. Lift the screwdriver to pry the front bezel away from the monitor.4. Continue around the edges until you can lift the back cover off the monitor.note: be careful around the corners. Take your time.
Reach in back of the switch bezel and pull up on it. The bezel will pop up and out of the door pull. This will allow you to remove the switch from the bezel.An instructional video has also been included below, to show how this process is accomplished.Hope this helps,1ATony
any electrical remove negative battery cable for your and cars saftey. toyota has a plastic bezel that covers radio climate controls get good lighting and look for two phillip screwg that hold bezel the rest are sping pins that pop out when pryed hint do not do dash work when plastic is ice cold plastic gets very brittle and will crack easy you can blast the heat for 20 minutes before you start go around bezel with a flat screwdriver and pop bezel off one clip at a time once this frame is off you will see four 10 mm bolts on each corner of radio remove bolts, grab radio firmly with both hands and pull straight out whilw wiggleing the radio pull it out far enough to remove connectors off back of radio. the antenea WIRE IS A SINGLE THICK WIRE THAT YOU PULL DIRECTLYOUT OF BACK OF UNIT THE CONNECTORS HAVE A SMALL LOCK BUTTON YOU MUST DEPRESS TO REMOVE I THINK THE ARE TWO HARNEES CONNECTORS AND ONE ANTENEA AN D ITS OUT ., YOU MIGHT HAVE TO PULL THE ASHTRAY OUT TO REMOVE BEZEL LOOK FOR MORE SCREWS THAT HOLD BEZEL AND ITS OUT PROBS EMAIL ME GOOD LUCK
There are different ways to remove fog from your watch. You use a blow dryer on low heat to blow warm air into the watch or just open the back of the watch and put it under direct sunlight to about two hours.
try taking off the little security bezel (buttons 2 - 5) and carefully flex the plastic to concave in the middle with the buttons facing you then put the bezel back in place. it used to do this with mine and i think the metal contacts on the back were not connecting. either that or when the radio switches itself off just push and hold the bezel down for a few seconds and it should hopefully come back on
remove the metal hinge or use a machete :)