Chevy S-10

How do you remove a window crank on a 1998 Chevy S10 pickup?

282930

Top Answer
User Avatar
Wiki User
2013-10-25 13:50:19
2013-10-25 13:50:19

There is a "C" clip behind the handle that must be removed. Your local auto parts store can sell you an inexpensive tool to help you remove the clip without damage done.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Remove the inside door panel of your 1997 Chevy Lumina. Remove the linkage to the window crank. Remove the window crank retaining bolts. Reverse the process to install the new window crank.

User Avatar

You have to remove the inside panel, where the window crank is, or would be.

User Avatar

Remove inside door handle and window crank handle, remove inside door panel, remove vent window and channel assembly, remove window.

User Avatar

A simple inexpensive tool is available at your local auto parts store. There is a C clip behind the handle that needs to be removed to release the handle.

User Avatar

There is a c-clipthat holds the crank in place,you just need to push it off and the crank comes off.

User Avatar

If you push back the door panel, you should see a retaining clip behind the center of the crank. Pull it out with a small needle nose pliers.

User Avatar

You will need to remove the inside door panel of your 1977 Chevrolet blazer. Remove the window crank linkage. Remove the window crank retaining bolts. Reverse the process to install the new window crank.

User Avatar

Remove the inside door panel. Remove the Allen screw from the window crank linkage. The window crank handles should come off.

User Avatar

You have to have a window crank remover, this tool looks like a U on a stick, and you slide this tool in between the the crank and the door panel and trip the lock pin, then the crank will pull off.

User Avatar

there is a C shaped clip behind the handle. I have the tool to remove it you can get them at auto zone. you can also use a small pick to pull clip out but watch out it will fling out

User Avatar

Most chevys have a horseshoe shaped clip on the window crank. There is a special tool to remove it , but I just push them off with a small screw driver, or hook the back with a dental tool

User Avatar

Pry the screwdriver between the door panel and the window crank base. Remove the metal clip slowly and carefully. Pull the base of crank to remove it.

User Avatar

IF there isn't a cover that unsnaps over IT-then U need a special slotted tool that goes behind the crank & pushes the C clip off-IT slides in right behind the window crank-ITS just a thin piece of metal that's slotted 2 push the clip off .

User Avatar

How to Remove or Install Car Window Crank Handles check related link below

User Avatar

You need to remove the window hand crank with a window hand crank removal tool.

User Avatar

To replace the window crank handle on the 1993 Geo Prism, first remove the interior door panel. Then, access the screw that holds the window crank in place and remove it. You can then remove the handle itself.

User Avatar

To remove the window knob,you need to purchase a tool at any auto parts store, you would then slide the tool behind the window crank and simply push out the clip that holds the window lever in place.

User Avatar

Window cranks are easy to remove. Go to the local auto parts store, and ask for a window crank removal too. Slip it in behind the crank until it comes free.

User Avatar

Pull out the U-clip located on the base of the window crank.

User Avatar

you can buy a window crank removal tool at an autoparts store that pulls the little pin off to remove it.

User Avatar

General Chevy info, remove door hande bezel, remove armrest, remove window crank if it has manual windows.(there is a clip on the crank) Start at the bottom and gently pry panel up pulling plasic clips out of holes in door. When panel is loose it will lift off of window ledge. If you have power windows or locks you will have to unplug the switches carefully

User Avatar

The window crank is held on by a "U" shaped clip. There is a special tool made to remove the clip. If you don't have the tool it can usually be pried out with a screw driver and a hook. Use the screwdriver to push out one side of the clip then pull the clip out with the hook.

User Avatar

To remove the window crank on the 1992 Toyota Paseo, first pry off the interior door panel. Then, access the screw that holds the crank in place. Remove the screw and the handle will come loose.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.