answersLogoWhite

0


Best Answer

The top seems to have a filler in it?????

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove and place back on an oil lamp top that has no threads?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Headlamp removal Toyota hiace?

In order to remove the headlamp of a Toyota Hiace, you must first remove the screws holding it in place. Then disconnect the electrical connector at the back of the lamp. You can then remove the headlight itself.


How do you replace license plate bulb on a 2000 dodge neon?

== # Remove screws attaching license plate lamp to rear bumper # Remove lamp from bumper. # Remove bulb socket from lamp. # Pull bulb from socket. == # Install bulb into socket. # Install bulb socket into lamp. # Place lamp in position. # Install screws attaching license plate lamp to rear bumper.


How do you change the reverse-backup light next to the tag on a 1996 Aurora?

Just remove the tag plate, there are mounting bolts (10mm)that hold the back-up lamp housing in place, remove them and a 1/4 turn socket to get to the lamp. Hope this helps, Ben Parker, San Jose, Ca.


How do you change fog lamp 2003 Cadillac STS?

Remove the rock guard behind the bumper to allow access to the back of the lamp in the bumper. Unhook the wiring harness from the lamp, and it will be a quarter turn to remove. Common bulb, can purchase anywhere.


How do you remove the front indicator light cover from a peugeot 205?

To remove the indicator from a 205, you need to remove the lamp first as far I am aware. 1) remove front grill, held in place by two screws on either side of the lamps. 2) now you can see springs on each side of the headlight. pull them back and remove lamp. 3) this should give u access to indicator housing. remove screws. the indicator is out!


How do you replace the headlight bulb on a 2004 Chevy Avalanche?

Open the hood. Above the headlights on each side you will find two L-shaped rods, held in place by plastic clips. Rotate the rods to release them from the clips. Lift them up and out of their holes. Now you should be able to remove the headlight assembly from out the front of the truck. Turn the lamp holder to remove it. Remove old lamp and replace. Goes back together just as easy. DO NOT TOUCH THE NEW LAMP WITH YOUR SKIN. Use a clean cloth to handle the new lamp.


If lamp switch is ON and if you remove the lamp bulb we still wasting electrict?

no because when you remove the lamp the circuit is still open; even if the switch is on


Replacing headlights on a 2002 grand prix?

remove entire light unit from under the hood remove bolts, lamp slides forward, replace bulb, slide unit back into place and bolt down, i think only two bolts, black


How do you replace the dome light bulb in a 2002 PT Cruiser?

DOME LAMP REMOVAL (1) Insert a trim stick or a flat headed screwdriver between the lamp unit and the lens. (2) Carefully swing down one side the lamp lens. (3) Remove lamp from lamp unit socket. INSTALLATION (1) Push lamp in socket and snap into place. (2) Position lens on lamp unit and snap into place.


How do you replace a headlight bulb on a 2004 Chevy Malibu?

Open the hood and pull up on the two black tabs on either side of the lamp assembly. Pull the lamp assembly forward gently and unclip the wiring harness. Twist the socket counter-clockwise and remove it. The bulb should be removed by wiggling it. Install new bulb in its place and turn the socket back into place. Reconnect the wiring harness and return the lamp to its original position. Line up the holes in the lamp assembly to the round ends of the mounting pins, and press down on the two black tabs to hook the lamp assembly into place.


How do you replace a headlight in a Hyundai XG 350?

Remove cap from back of lamp release pin replace bulb


How do you replace the side marker lamp on a 97 Jetta?

Remove the connector from the back of your 1997 VW Jetta side marker lamp. Take hold of the side marker lamp, push in and turn at the same time. The lamp will come out. Reverse the process to install the new side marker lamp.