answersLogoWhite

0


Best Answer

I'm going to assume that it is similar to the cover on the 1997 Deville Concours. In the '97 you simply 'pull up' on the cover. It has prongs that press and snap into receiver ports in the vehicle proper.

User Avatar

Wiki User

14y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you remove maxifuse relay cover on 1998 cadillac deville?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Art & Architecture

Where is the starter fuse for a 1987 Cadillac DeVille?

29s here, i work for an automotive company a recently we had a 94 or 95 caddy deville with the north star engine in for a starter replacement. the starter was located in the center of the motor! the engine is a v-shape (v8) with the intake cover acting as a lid overtop of the motor with the starter smack in the center. you would have to remove the intake in order to even see the starter if you have the same motor types. That is exactly how to remove it on a 97, i have one and the starter is located under the intake.


How do you adjust the ford puma handbrake?

Remove the plastic cover from the puma handbrake. There is an adjustment nut under the cover that tightens up the brake.


How do you remove the window handle from a 1995 dodge Dakota?

Pop back the plastic cover from the center of the crank and remove Allen or Philips screw. Handle will then pull off.


How do you replace the valve cover gasket on a 1990 Honda Civic 1.5L FI and how much would it cost?

First remove spark plug wires from the top of the valve cover. then remove bolts or nuts around the edge of valve cover. once removed. take off cover and replace o-rings and gasket. gasket is located around edge of cover and o-rings are o shaped rubber gaskets on the cover around the holes where the wires normally go through. be sure to replace cover the same way you remove it. estimated cost would be $35 for just gasket and 0-rings it is recommended to also replace wires and spark plugs when doing this.that cost would be 60-$90 depending on make of vehicle.


How do you remove plaster from concrete block walls?

With a masonry chisel. It may be easier to cover it with a new surface.

Related questions

How do you remove valve cover gasket on a 2000 Cadillac DeVille?

remove right valve cover on cadilac sts


How do you remove the front valve cover on a 1996 deville northstar engine?

you dont. a cadillac tech does


Where is the blower motor located in a 2003 Cadillac deville?

Right side under dashboard. Remove plastic cover then look for a Round plastic cover.


How do you remove the radio from a 1993 Cadillac Deville?

Remove the decorative radio cover. Remove the radio retaining screws. Slide the radio out. Remove the wiring harness from the back of the radio.


Where are the fuses in a 1969 Cadillac deville?

The fuses in a 1969 Cadillac Deville are under the dash on the driver's side. Look above and behind the brake pedal for a plastic cover over the fuse box.


Where is starter located on 1999 cadillac deville?

its located under the engine cover in between the heads


Whwre is the PCV valve on a 2002 cadillac deville?

Mine does not have one! Some do, and it is on the rear valve cover.


Where is the turn signal flasher located on a 1994 cadillac deville concourse?

The flasher is located under the dash right under the steering colum. remove the underdash cover and it willbe to the right of the colum.


How do you disconnect trunk pull down motor for 94' cadillac Deville?

Remove the plastic cover inside the trunk that surrounds the motor. There should be a connect at the bottom of the motor on the right side. Disconnect it there.


How do you remove valve cover gasket on 1997 Cadillac catera?

i am going to change the valve cover gasket on my 97 cadillac catera, what do i need to remove and do? Is it hard?


Where can you find a 97 Cadillac Deville Fuse Box Diagram?

This is typicall attached to the inside cover of the fuse box


How do you remove the head on a Cadillac DeVille?

Any obstructions such as the intake must be removed first. This will depend on the model. The valve cover is removed, along with the rocker arms and push rods. The head can then be unbolted and removed.