0
This should help. I have this same motorcycle and the basic instructions below are correct. One side-note is that to get the wheel past the caliper, it can help to deflate the tire to make it narrower.
Instructions below found at:
http://motorcycle.justanswer.com/questions/1ayag-remove-rear-wheel
*************
In addition to the obvious of elevating the back of the motorcycle to get the weight off the rear tire, you need to unbolt the final drive from the swing arm and remove the final drive and rear wheel as an assembly. The drive shaft will come out with the final drive, not a problem.
Once you get the assembly off the bike, you can remove the axle then separate the final drive from the rear wheel and do what you needed to do.
When you go to re-install the drive shaft, you have to align the splines. Sometimes it is easier to put the bike in gear so the female splines on the intermediate shaft don't turn as you rotate the rear wheel to insert the drive shaft.
When you go to put it back together, just tighten the bolts that hold the final drive to the swing arm evenly in a crossing pattern until tight.
As an aside note, while you have it off, make sure you grease the splines on the end of the drive shaft and the splines for the rear wheel before putting it back together.
What else can I help you with?
Remove rear wheel on Yamaha V Star 1100?
how do you check oil on Yamaha v star classic 1100
How do you remove the final drive from the rear wheel of a 2006 v star 1100?
To remove the final drive from the rear wheel of a 2006 V Star 1100, first, ensure the bike is securely supported on a stand. Remove the rear wheel by loosening the axle nut and detaching the wheel from the swingarm. Next, disconnect the final drive by removing the bolts securing it to the swingarm and sliding it off the drive shaft. Finally, ensure all components are properly labeled for reassembly.
Will a gas tank from a 2003 v star fit a 1999?
650 OR 1100 ? CLASSIC OR CUSTOM?
What is the gas tank size on a 2003 vstar 1100 custom?
2003 Yamaha V Star 1100 - Service manualTypeFuel tank capacity 17 L (4.49 gal.)Fuel reserve amount 4.5 L (1.18 gal.)Regular unleaded gasoline
Will 1100 vstar coils work on a 650 vstar?
Will v star 1100 coils work on 650 v star
Where is the fuse box for Yamaha v star 1100?
Where is the fuse box on a 2002 1100 V star Yamaha
How do you remove seat v star 1100?
To remove the seat on a Yamaha V-Star 1100, start by locating the seat release mechanism, usually found at the back of the seat. Use a key or a flathead screwdriver to unlock it, then lift the seat off the motorcycle. If there are additional bolts or screws securing the seat, remove those with the appropriate tools. Always refer to your owner’s manual for specific instructions related to your model.
What is the O.D. of a v star 1100 rear hub?
The outer diameter (O.D.) of a V Star 1100 rear hub is approximately 4.75 inches (120.65 mm). This dimension is important for ensuring compatibility with the wheel and brake components. Always check with manufacturer specifications or service manuals for precise measurements and installation guidance.
Where is the key code on a 2003 Yamaha v star classic 1100?
On the Barrel of the ignotion (where you stick your key) the barrel WILL have to be removed from its housing to read the code printed on there.
Will the 1100 v stars wheels interchange with the 650 v star?
Yes, the 650 wheels will interchange with the 1100 wheels on V-Star. They will also interchange with the Road Star. -- Zioo1
How do you remove front fender on Yamaha vstar 1100?
To remove the front fender on a Yamaha V-Star 1100, start by securing the motorcycle on a stable surface and removing the front wheel for easier access. Unscrew the fender mounting bolts located on the underside of the fender, typically at the fork legs. Carefully detach any wiring or brake line brackets connected to the fender, then gently lift the fender off the motorcycle. Always consult your owner’s manual for specific details and torque specifications.
What is the top speed of a v-star 1100?
110mph
