OK this is the most complicated thing i have ever seen so ya might wanna take it to a shop this is in my rendezvous repair book good luck
-Remove the battery ground (negative) cable from the battery. -Rotate and secure the engine forward to access rear generator bolts. -Remove the generator B+ terminal nut. -Remove the generator B+ lead. -Remove the generator electrical connector. -Remove the drive belt from the generator. -Remove the generator front bolt. -Remove the generator rear bolts. -Remove the generator from the generator bracket and position the generator above the drive axle. -Remove the drive belt tensioner. -Remove the generator bracket. -Remove the Power Steering pipes from the power steering pipe retainer. -Remove the fuel pressure test port (schrader valve) cap from the fuel injector rail. "Important" Do not disconnect the power steering pipes from the power steering pump. -Remove the power steering pump and reposition the power steering pump in front of the timing chain cover in order to provide access for the generator. -Remove electrical harness from retainer on right fender well and position aside. -Remove the generator from the vehicle.
-Install the generator to the vehicle and position the generator above the drive axle. -Install electrical harness to retainer on right fender well. -Install the power steering pump to the engine. -Install the fuel pressure test port (schrader valve) cap to the fuel injector rail. -Install the power steering pipes from the power steering pipe retainer. -Install the generator bracket. Refer to Generator Bracket Replacement . -Install the drive belt tensioner.. -Install the generator to the generator bracket and position the generator above the drive axle. -Install the drive belt tensioner. -Install the generator to the generator bracket. -Install the generator front bolt. *Notice* Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems. -Install the generator rear bolts. Tighten Tighten the generator bolts to 50 N�m (37 lb ft). -Install the drive belt. -Install the generator electrical connector. -Install the generator B+ lead. -Install the generator B+ terminal nut. Tighten -Tighten the generator B+ terminal nut to 13 N�m (115 lb in). -Rotate the engine rearward and install the engine mount strut bracket bolts -Install the battery ground (negative) cable to the battery.
BBAASPENCER here in TN. This is how to roll it forward for access.Roll the engine forward is to take off the engine dog bones, put gear in neutral, attach a pulling strap to the engine and hoist and roll it until you gain access.
How do you remove steering pump on a 2002 Buick rendezvous 3.4L?
how do i change starter on buick 2002 rendezvous
how to replace starter for a 2002 buick rendezvous
2002 buick rendezvous ambiant temperature sensor location
If you remove the pan, you will see the filter up in the transmission.
will the dash lights work if we use a bcm out of a different 2002 buick rendezvousand put it in my 2002 buick rendezvous
How much can cost repair to change head gasket Buick Rendezvous 2002
The 2002 Buick Rendezvous has a 3.4 V6. Firing order is 1-6-5-4-3-2.
YES A Rendezvous does has a shock and a strut on the rear.
my 2002 has 10 liters
The fuel tank has to be removed, as the pump is in the tank. The pump takes a special tool to remove.
The ECU/BCM on the 2002 Buick Rendezvous CX is located underneath the Driverside seat.
how do i remove a alternator
steps to remove 2002 9-3 alternator
replace 2002 buick rendevous motor mount
All Buick Rendezvous were virtually indentical from 2002-2007.
Remove the belt from your 2002 Chevy Cavalier alternator. Remove the wiring harness from the back of the alternator. Remove the alternator retaining bolts. Reverse the process to install your new alternator.
Remove door panel, then three bolts on mirror inside the speaker housing area.
One would look for a used 2002 Buick Rendezvous in Denver by going the site of Auto Trader. There, one could find various models of used Buick and one could bargain for a good price.