0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How do you replace the headlight bulb located on a Pontiac Grand Prix model years 1996-2003 all trim levels?
With the hood open remove the (2) two headlamp assembly bolts from the upper fascia support. Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support. Position the headlamp assembly away from the vehicle body to access the electrical connector. Disconnect the electrical connector from the headlamp assembly. Remove the headlamp assembly from the vehicle. If you wish to change the halogen bulb: Disconnect the electrical connector from the headlamp bulb/socket. Remove the headlamp bulb/socket retainer ring from the headlamp, by turning counterclockwise. Remove the headlamp bulb/socket from the headlamp assembly. Hope this helps. G These instructions are similar from around '96 to '03 grand prix model years all trim levels.
How do you remove the headlamp assembly on a 2003 Subaru Forester for changing the light bulbs inside the assembly?
I have a 1999 Forester, but I imagine the 2003 is similar in this regard. You don't actually need to remove the headlamp to replace the bulb. On my car, I unplug the wire from the bulb at the back of the headlamp, remove the large rubber piece around the back of the bulb, unclip the clips that hold the bulb in place, remove and replace. Cheers! Mark This is a good answer and is so just as stated. Thanks Mark! RicT
How do you change a headlight bulb on a 2003 s-10 Chevy?
Standing in front of the bad headlamp, with the hood open, notice the two black tabs sticking up behind the headlamp assembly. These are locks that hold the headlamp assembly in place. Remove the locks by wiggling and pulling straight up. Now the headlamp assembly will drop out the front far enough to twist out the bulb socket to change the bulb. Reverse for installation.
How do you change the headlamp bulb in a 2003 Grand Prix?
Caution Halogen bulbs contain gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments. To help avoid personal injury: Turn off the lamp switch and allow the bulb to cool before changing the bulb. Leave the lamp switch OFF until the bulb change is complete. Always wear eye protection when changing a halogen bulb. Handle the bulb only by its base. Avoid touching the glass. Keep dirt and moisture off the bulb. Properly dispose of the used bulb. Keep halogen bulbs out of the reach of children. Raise the hood. Remove the headlamp assembly bolts from the upper fascia support. Slide the headlamp assembly outward enough to release the headlamp bracket tabs from the slots in the upper fascia support. Position the headlamp assembly away from the vehicle body to access the electrical connector. Disconnect the electrical connector from the headlamp assembly. Remove the headlamp assembly from the vehicle. Disconnect the electrical connector from the headlamp bulb/socket. Remove the headlamp bulb/socket retainer ring from the headlamp, by turning counterclockwise. Remove the headlamp bulb/socket from the headlamp assembly.
How do you remove headlight assembly?
How to remove headlight assembly on 2003 Lexus GX470
How do you change nearside front headlamp bulb on mondeo 2003?
2 sliding bars hold headlight in remove and pull headlamp forward and out
How do you change the headlamp on a 2003 Chevy s-10?
Remove the entire headlight assembly to gain access to the headlight bulbs. To do this simply open the hood, pull up and out the two plastic locks that hold the assembly in place then wiggle the assembly out the front. Once you have done one you will find it easy.
How do you replace the low beam headlamp on a 2003 Nissan Altima?
You must remove the front bumper!
How do you replace the headlight bulb on a 2001 Pontiac Grand Prix?
See posting for "How do you change the headlamp bulb in a 2003 Grand Prix?" All these model years are similar in production for the headlamp assembly.
How do you change the headlights in a 2003 Chevy Trailblazer?
I have a 2002 Trailblazer it took me forever to figure this out. To remove the headlamp assembly on a Trailblazer, remove the plastic panel that covers the hood latch assembly, remove the grill then release the retainers for the headlamp assemly. The bottom retainers for the grill are tricky and difficult to release. you can break the grill if done incorrectly. I'm told there is a way to change the bulbs without removing the grill but it seems to involve bending the grill in half and some severely scraped knuckles.
How do you remove the headlamp from a Vw polo 2003?
First, the rubber cover on the back of the bulb must be removed. Remove the connector, then loosen the torque screws. The locking ring can now be turned counter-clockwise in and the headlamp can be taken out.
How do you change a headlamp on 2003 expedition?
***CAUTION***The halogen bulb contains gas under pressure. The bulb may shatter if the gas envelope is scratched or if the bulb is dropped. Handle the bulb carefully. Grasp the bulb only by its base. Avoid touching the glass envelope. è The headlamp bulb should not be removed from the headlamp until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp. Headlights Removal & Installation 1. Raise and support the hood. 2. Raise the headlamp retainers by pushing rearward and pulling up. 3. If equipped, rotate the headlamp bulb protective counterclockwise and remove. 4. Disconnect the headlamp bulb electrical connector. 5. Remove the headlamp assembly. 6. Rotate headlamp bulb retainer counterclockwise and remove. 7. Remove the headlamp bulb by pulling it straight out with a gentle up-and-down rocking motion. ***WARNING*** Do not touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation. To Install; 8. Install a new bulb into the headlamp assembly. 9. Install the headlamp bulb retainer and turn it clockwise to engage the retaining tabs. 10. Attach the bulb electrical connector. 11. If equipped, install the headlamp bulb protective cover. 12. Install the headlamp assembly. è Be sure the headlamp assembly is positioned correctly with the alignment pins inserted into the proper holes and onto the ribs of the reinforcement. 13. Engage the retainers by gently pushing down. 14. Turn the lights on and check the bulb operation.
